Abstract:Introduction Water electrolysis is expected a key device to introduce large-scale renewable electricity under management of power grid and electrification of non-electric sector. While alkaline water electrolysis (AWE) systems are well-developed large system, degradation under fluctuated operation with start and stop operation is significant issue to combine photovoltaic and/or wind turbine generation is significant issue. In this study, we have been investigated reverse current, which is leak current through manifold of bipolar alkaline water electrolyzers, and electrode potential behavior of stop operation, and proposed accelerated durability test (ADT) protocol for start and stop operation. Experimental and modeling Figure 1 shows configuration of 4-cells bipolar alkaline water electrolyzer that was consisted with end plates of EP(-) and EP(+), bipolar plates of BP1 to BP3, anodes, separators, and cathodes with principle of reverse current. The end and bipolar plates were made of nickel. Anodes and cathodes were commercially available oxygen and hydrogen electrocatalyst coated nickel mesh electrodes (De Nora Permelec Ltd) with 27.8 cm 2 of projected area. Zirfon Perl UTP500 (Agfa) was used for separators. Manifolds were made of Teflon tubes and 15 mL/min of 7 M (= mol/dm 3 ) was circulated for each anolyte and catholyte chambers during measurements. An anode and a cathode set on a bipolar plate. During operation anodes and cathodes are oxidized and reduces, respectively. After stop, the anode and the cathode on a bipolar plate connects both electronically and ionically, so oxidized anode and reduced cathode surface discharges to same potential. In this study, we measured electrode potential and reverse current after 1 h water electrolysis of 80 o C at 0.6 A/cm 2 . The reverse current was measured ionic current through communicating tube with D. C. clamp meter (KEW2510, Kyoritsu). Reverse current behavior was analyzed with COMSOL Multiphysics version 5.5 based 2-dimensional model of stack and height direction using experimentally anode and cathode potentials as functions of discharge for anode and cathodes. Results and discussion Figure 2 shows cell performances in the stacks and a picture of the lab-scale zero-gap configuration electrolyzer. All cells in a stack showed almost the same performance. The cell voltage was 2 V at 400 mA/cm 2 at 30 o C and was 1.8 V at 500 mA/cm 2 at 80 o C. Therefore, we think all cells and parts work well. Figure 3 shows reverse currents and electrode potentials as a function of time after 1 h electrolysis under 600 mA/cm 2 at 30 or 80 o C. Here, the dashed lines in Fig. 3-a) were simulated value and were almost same after 20 s. The measured reverse current increased around 20 s. At this moment, outlet manifolds filled with electrolyte to increase ionic conduction among the chambers, which was not considered in the simulation. After degassed of manifolds, the reverse current decreased with time with the largest reverse current for the BP2. The reverse current at 80 o C was significantly larger than that at 30 o C. This difference could be explained the dependence of ionic resistance of manifold on temperature. At same moment, anode and cathode potentials on the end plates were almost constant. The anode cathode potentials on the bipolar plates decreased and increased with time, respectively. Both anode and cathode showed significantly potential change region. The final potentials of all electrodes were around 0.9 V vs. RHE. The potential change regions of the electrodes on the BP2 were earlier than others. Here, the anode and cathode potentials as functions of discharge were almost same for the electrode on all bipolar plates. Therefore, the average discharge functions for anode and cathode were treated as characteristics of electrodes of this study. Using this function, reverse current as a function of time could be expressed accurately using the developed model. From this model, reverse current, and electrode potentials as a function of time would be expected with discharge function of each electrode and ionic resistance of manifold. Figure 4 shows that a start & stop operation simulated ADT protocol based on bipolar electrolyzer measurements. We propose the combination of constant current electrolysis, potential sweep, and chronoamperometry as the inset of illustration in Fig. 4, because constant current measurement is easier to get reproductivity in high current that need accurate iR correction for constant potential measurement and current control measurement never simulate stop operation. Acknowledgements -Abstract Truncated-

Sensitivity analysis of the process conditions affecting the shunt currents and the SEC in an industrial-scale alkaline water electrolyzer plant

Influence of shunt currents in industrial-scale alkaline water electrolyzer plants

Mathematical Modeling and Experimental Validation for a 50 Kw Alkaline Water Electrolyzer

Plant-wide Modeling, Design Consideration, and Practical Hierarchical Control Strategy Considering Key Variable Integral Characteristics for an Industrial Alkaline Water Electrolyzer Plant

Performance Analysis of Alkaline Water Electrolysis System Based on Heat Current Modeling Method

Numerical modeling and analysis of the effect of pressure on the performance of an alkaline water electrolysis system

Mathematical Modeling and Simulation for External Electrothermal Characteristics of an Alkaline Water Electrolyzer

Experimental and modeling study on energy flow of 250 kW alkaline water electrolysis system under steady state conditions and cold start process

Differential algebraic modeling of an alkaline electrolyzer plant

Dynamic Simulation and Performance Analysis of Alkaline Water Electrolyzers for Renewable Energy-Powered Hydrogen Production

Quantifying Temperature Effects in Large-Scale PEM Water Electrolysis Stacks

(Invited) Leak Current Analysis of Stop Operation and Its Modeling for the Development of Bipolar Alkaline Water Electrolyzer Electrodes

Optimizing Alkaline Water Electrolysis: A Dual-Model Approach for Enhanced Hydrogen Production Efficiency

Multi-physics model development and application to real-case alkaline electrolyzer

Alkaline Water Electrolysis – Investigation of the Charge Transport Limitations across the Separator Under Low KOH Concentration

Investigation of the operation characteristics and optimization of an alkaline water electrolysis system at high temperature and a high current density

(Energy Technology Division Graduate Student Award sponsored by BioLogic) In-Situ Diagnostic Tools and Analysis to Identify Root Causes for Voltage Losses in Anion Exchange Membrane Water Electrolyzers

Analysis of the Effect of Characteristic Parameters and Operating Conditions on Exergy Efficiency of Alkaline Water Electrolyzer

Control-oriented dynamic modeling and thermodynamic analysis of solid oxide electrolysis system

A Comprehensive Review of Alkaline Water Electrolysis Mathematical Modeling

Thermal Modeling and Controller Design of an Alkaline Electrolysis System under Dynamic Operating Conditions