Abstract:Biomass residues are crucial feedstocks for facing climate change challenges due to high-value products, such as producing activated carbons (AC) for carbon capture. Two stages of pyrolysis followed by activation at high temperatures are the most used technique for converting lignocellulosic precursors into porous activated carbons. This process has shown to offer the highest surface areas; however, a two-stage process is undesirable as is an energy-intensive processes. Product characteristics are affected by feedstock and reaction rate conditions. In the present study pine wood (PW), olive stones (OS) and pecan nutshells (NS) were evaluated as feedstocks in the production of AC for selective post-combustion CO 2 capture via a single-step pyrolysis-activation using microwave heating. Direct raw biomass impregnation was completed using potassium hydroxide (KOH). The ACs were synthesised in 8 min using 300 W of microwave power with 8.8 GJ t −1 specific microwave energy input. Samples exhibited large specific surface areas (S BET ), up to 1340 m 2 g −1 , with 70 % of ultra-micropores (<0.8 nm), fundamental for high CO 2 adsorption capacity. Among the tested biomasses, PW was the best performing and physicochemical characterisation and CO 2 capture studies indicated that PW-based AC has 79 % carbon, amorphous structure, and possessed larger ultra-micropores that resulted in high CO 2 /N 2 selectivity (12.5), and one of the largest CO 2 uptakes for ACs (6.2 and 4.2 mmol/g at 0 and 25 °C, respectively). The CO 2 performance was investigated across a range of temperatures up to 100 °C, while cyclic regenerative performance was confirmed after 15 adsorption–desorption cycles. This study highlights the development of AC from different lignocellulosic resources by a fast and low-energy single microwave-pyrolysis activation process that can produce ultra-microporous structures implemented in post-combustion CO 2 capture.

Sustainable production of porous carbon from biomass: Influence of pre-carbonization on pore evolution and environment impact

Activation of mixed sawdust and spirulina with or without a pre‐carbonization step: Probing roles of volatile-char interaction on evolution of pyrolytic products

Activation of Poplar Sawdust and Anthracite Coal: Distinct Involvement of Aliphatic and Aromatic Structures in Pore Development

Enhanced Abundance of Oxygen-Containing Intermediates from Pre-Oxidation of Poplar Sawdust Facilitates Generation of Porous Structures in Activation with Phosphoric Acid

Importance of oxidation reactions in creating pores in physical activation of biomasses

Syngenetic Effects in Co-Activation of Willow Wood with Homogenous Biochar Facilitate Pore Generation in Activation

Impacts of partial removal of lignin on development of pore structures in activation of Chinese parasol

Efficient preparation of carbon nanospheres-anchored porous carbon materials and the investigation on pretreatment methods

Real-time monitoring the carbonization and activation process of activated carbon prepared from Chinese parasol via zinc chloride activation

Influence Of Coal Preoxidation On The Porosity Of The Activated Carbons With Steam Activation

The effects of pore structures and functional groups on the catalytic performance of activated carbon catalysts for the co-pyrolysis of biomass and plastic into aromatics and hydrogen-rich syngas

Enhancing biochar production: A technical analysis of the combined influence of chemical activation (KOH and NaOH) and pyrolysis atmospheres (N2/CO2) on yields and properties of rice husk-derived biochar

Enhancing biochar production: A technical analysis of the combined influence of chemical activation (KOH and NaOH) and pyrolysis atmospheres (N 2 /CO 2 ) on yields and properties of rice husk-derived biochar

Effects Of Carbonization On The Co-Activation Of Sludge And Biomass To Produce Activated Coke

Efficient Production of Activated Carbon with Well-Developed Pore Structure Based on Fast Pyrolysis-Physical Activation

Preparation of Activated Carbon from Co-Pyrolysis Activation of Fly Ash and Biomass

Thermal pretreatment of willow branches impacts yield and pore development of activated carbon in subsequent activation with ZnCl2 via modifying cellulose structure

An overview on engineering the surface area and porosity of biochar

The Role of Lignin Molecular Weight on Activated Carbon Pore Structure

Single-step preparation of activated carbons from pine wood, olive stones and nutshells by KOH and microwaves: Influence of ultra-microporous for high CO 2 capture

Effects of raw material texture and activation manner on surface area of porous carbons derived from biomass resources.