Abstract:The research presented in this article was conducted to evaluate the suitability of recycled foam concrete (RFC) as an ingredient in newly created cement mortars. The basis for an analysis was the assumption that the waste is collected selectively after separation from other waste generated during demolition. The motivation for the research and its main problem is a comparison of the performance of RFC used in various forms. RFC was used in two forms: (1) recycled foam concrete dust (RFCD) as a 25 and 50% replacement of cement, and (2) recycled foam concrete fine aggregate (RFCA) as a 10, 20, and 30% replacement of sand. The basic properties of fresh and hardened mortars were determined: consistency, density, initial setting time, absorbability, compressive strength, thermal conductivity coefficient, and heat capacity. Research is complemented with SEM observations. The properties of fresh mortars and mechanical parameters were decreased with the usage of any dosage of RFC in any form, but the thermal properties were improved. The required superplasticizer amount for proper consistency was raised four times for replacing cement with 50% of RFCD than for 25% of such replacement. The mix density dropped by about 8% and 9% for mortars with the replacement of 50% cement by RFCD and 30% sand by RFCA in comparison to reference mortar. A 30% decrease in initial setting time was observed for cement replacement. In the case of sand replacement, it was the opposite—an increase of 100%. The dry density decreased by about 14% and 11% for mortars with the replacement of 50% cement by RFCD and 30% sand by RFCA in comparison to reference mortar. Absorbability was raised by about two times after replacement with both RFCD and RFCA. Compressive strength after 28 days dropped significantly by 75% and 60%, and the thermal conductivity coefficient decreased by 20% and 50% with 50% RFCD added instead of cement and 30% RFCA replacing sand. It indicates greater efficiency in thermomechanical means from RFCA in comparison to RFCD. This material can be used especially in the production of plaster and masonry mortar. Linear correlations of dry density and thermal conductivity coefficient and the latter and compressive strength were proven as reliable for RFCD replacement of cement and RFCA replacement of sand in mortars with greater w/c ratio.

Effect of chemically modified recycled carbon fiber composite on the mechanical properties of cementitious mortar

Effect of Fiber on Mechanical Properties of Cement Stabilized Macadam Mixture

Synergic Effect of Recycled Carbon Fibers and Microfibrillated Cellulose Gel for Enhancing the Mechanical Properties of Cement-Based Materials

Experimental study on mechanical property and microstructure of cement mortar reinforced with elaborately recycled GFRP fiber

Influence of Cementitious Material Infiltration on Piezoresistive Effect of Carbon Fiber Bundle

Enhanced Compatibility of Secondary Waste Carbon Fibers through Surface Activation via Nanoceramic Coating in Fiber-Reinforced Cement Mortars

Mechanical behavior of a cementitious composite incorporating flax fibers treated with citric acid

Fresh, Mechanical, and Thermal Properties of Cement Composites Containing Recycled Foam Concrete as Partial Replacement of Cement and Fine Aggregate

Effect of Nano Compound Addition on the Properties and Microstructure of Cement Mortar with Mixed Fine Recycled Aggregate

Enhanced early hydration and mechanical properties of cement-based materials with recycled concrete powder modified by nano-silica

Effects of pretreated recycled fine aggregates on the mechanical properties and microstructure of alkali-activated mortar

Experiment and molecular dynamics simulation of functionalized cellulose nanocrystals as reinforcement in cement composites

The Properties of Composites with Recycled Cement Mortar Used as a Supplementary Cementitious Material

Effects of recycled carbon fibers on mechanical and piezoresistive properties and environmental impact in alkali-activated cementitious materials

Role of recycled concrete powder as sand replacement in the properties of cement mortar

Experimental Study on the Strength and Hydration Products of Cement Mortar with Hybrid Recycled Powders Based Industrial-Construction Residue Cement Stabilization of Crushed Aggregate

Fabric-Reinforced Cementitious Matrix (FRCM) Carbon Yarns with Different Surface Treatments Embedded in a Cementitious Mortar: Mechanical and Durability Studies

Effect of multi-walled carbon nanotubes on the damping property of cement mortar and mechanism analysis

Conjoint Reuse of Ceramic Polishing Waste and Calcium Carbide Slag As Mineral Admixtures: Hydration and Mechanical Properties

Experimental investigation on the effect of incorporating nanomaterials on some properties of self-compacting cementitious mortar

A Study on the Mechanical and Wear-Resistance Properties of Hybrid Fiber Mortar Composites with Low Water-Cement Ratios