Research on Cogging Torque Reduction of Direct-Drive Type Dual-Rotor Radial Flux Permanent Magnet Synchronous Motor for Electric Propulsion Aircraft

Haomin Li,Minglu Feng,Li Lei,Yingsan Geng,Jianhua Wang

DOI: https://doi.org/10.3390/en17071583

IF: 3.2

2024-03-27

Energies

Abstract:The direct-drive type high-torque-density motor is one of the most promising solutions of electric propulsion for aircraft. The cogging torque of the direct-drive motor causes torque ripple, vibration, and noise, which seriously affect the stability and reliability of the electric propulsion system for aircraft. In this paper, a novel direct-drive type high-torque-density dual-rotor radial flux permanent magnet synchronous motor (DRPMSM) is proposed, and its cogging torque is weakened by permanent magnet shape design and pole-arc coefficient combination. An eccentric and chamfered permanent magnet shape is proposed, and the influence of eccentric distance and chamfer angle on cogging torque is clarified. Through the pole-arc coefficient combination design of the inner and outer rotors of the DRPMSM, the cogging torques of the inner and outer rotor are phase reversed, thus further reducing the total cogging torque of the DRPMSM. By employing the response surface method, a mathematical model is established for the cogging torque of the DRPMSM in relation to the pole-arc coefficients, chamfer angle, and eccentric distance of the permanent magnets. The parameters that minimize the cogging torque of the DRPMSM are obtained using a genetic algorithm. A prototype is manufactured according to the optimized parameters, and experimental results validate the correctness of the theoretical analysis and the effectiveness of the optimization design method.

energy & fuels

What problem does this paper attempt to address?

### Problems Addressed by the Paper

The paper primarily explores the issue of reducing cogging torque in high torque density direct-drive dual-rotor radial flux permanent magnet synchronous motors (DRPMSM) used for electric propulsion aircraft.

#### Background and Motivation
With air traffic expected to triple by 2050 and account for 20% of global greenhouse gas emissions, electric propulsion aircraft have become an inevitable choice to address global environmental challenges. These aircraft use electric energy as the power source for the propulsion system, with the drive motor being the core component of the entire electric aircraft propulsion system. For propeller direct-drive propulsion motors, the output speed is strictly limited by the propeller speed, making high torque density a more critical parameter. Additionally, since the direct-drive motor is directly coupled with the propeller, the motor's output torque ripple directly affects the stability of the motor-propeller system. Therefore, increasing the torque density and reducing the torque ripple of the propeller direct-drive motor are key factors in the development of electric propulsion aircraft.

#### Main Issues
This paper specifically focuses on the cogging torque issue of dual-rotor radial flux permanent magnet synchronous motors (DRPMSM). Due to its dual air-gap structure, the cogging torque of DRPMSM is usually larger than that of traditional permanent magnet motors. Cogging torque is the main cause of torque ripple, which can lead to speed fluctuations, mechanical vibrations, and noise in the motor-propeller system. Particularly at low speeds, it can also cause a decrease in the efficiency of DRPMSM. Therefore, reducing cogging torque is one of the key issues in designing propeller direct-drive DRPMSM.

#### Solutions
To reduce the cogging torque of DRPMSM, the paper proposes the following methods:
1. **Permanent Magnet Shape Design**: A design with eccentricity and chamfering of the permanent magnet shape is proposed. By changing the eccentric distance and chamfer angle, the unilateral cogging torque is weakened.
2. **Pole Arc Coefficient Combination Design**: By combining the pole arc coefficients of the inner and outer rotors, the cogging torque phases of the inner and outer rotors are made opposite, thereby further reducing the total cogging torque of DRPMSM.

A mathematical model of DRPMSM cogging torque concerning pole arc coefficient, chamfer angle, and eccentric distance was established using the response surface method. The genetic algorithm was used to optimize and obtain the parameter combination with the minimum cogging torque. A prototype was manufactured based on the optimized parameters, and experiments were conducted to verify the correctness of the theoretical analysis and the effectiveness of the optimization design method.