Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes ( d ̄ ) were used for two-stage tensile tests under the conditions with distinct pre-strain εpre and intersection angle θSPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing εpre and θSPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d ̄ . This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre-strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

An extended mesoscaled M-K model for predicting discrete ultimate strains and evaluating the effect of normal stress on forming limits

Constitutive Model of Aviation Aluminum-Alloy Material in Metal Machining

An improved Marciniak-Kuczynski approach for predicting sheet metal formability

Forming limit of hot-rolled high-strength steels considering sheet thickness effect

A constitutive model on flow stress prediction from the contribution of twin and grain refinement, strain and strain rate during surface mechanical attrition treatment of metals

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Feasibility evaluation of failure models for predicting forming limit of metal foils

Modelling of ultra-thin steel sheet in two-stage tensile deformation considering strain path change and grain size effect and application in multi-stage microforming

M–K Ductile Damage Theory Predicts Formability of Stainless Steel Ultra-Thin Strips in Stamping

Formability prediction of high‐strength steel sheet using experimental, analytical and theoretical analysis based on strain and stress forming limit curves and its application to automotive forming parts

A new ductile failure criterion for micro/meso scale forming limit prediction of metal foils considering size effect and free surface roughening

Damage and forming limit analysis in porous ductile sheet metals at room or elevated temperatures

Experiment and modeling based studies of the mesoscaled deformation and forming limit of Cu/Ni clad foils using a newly developed damage model

Research on incremental forming simulation based on an improved constitutive model

M–K model based forming limit prediction of aluminum–lithium alloy 2060 and its application in hot stamping

A microscale constitutive model for thin stainless steel sheets considering size effect

Modeling of the Friction Behavior in Metal Forming Process Considering Material Hardening and Junction Growth

A Generalized Stress State and Temperature Dependent Damage Indicator Framework for Ductile Failure Prediction in Heat-Assisted Forming Operations

Enhancing/Improving Forming Limit Curve and Fracture Height Predictions in the Single-Point Incremental Forming of Al1050 Sheet Material

Forming Limit Evaluation with Perturbation Approach Considering Through-Thickness Normal Stress

Crystal plasticity modelling of multi-stage deformation of ultra-thin sheets considering grain size effect and strain path change