Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

Study of RP-3/n-butanol fuel spray characteristics and ANN prediction of spray tip penetration

Spray characteristics of diesel, biodiesel, polyoxymethylene dimethyl ethers blends and prediction of spray tip penetration using artificial neural network

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Experimental study on the spray characteristics of octanol diesel and prediction of spray tip penetration by ANN model

Integrating properties and conditions to predict spray performance of alternative aviation fuel by ANN model

Development and validation of a detailed kinetic model for RP-3 aviation fuel based on a surrogate formulated by emulating macroscopic properties and microscopic structure

Combustion characteristics of RP-3 aviation kerosene/n-butanol blended fuel in a compression ignition engine

Development and Validation of Small-Size Mechanism for RP-3 Aviation Fuel with High Precision

Characterizing Combustion Performance and PM Emissions of an Aviation Compression Ignition Engine by Fueling RP-3 Kerosene and RP-3/pentanol Blends

Effects of Fuel Properties on Under-Expansion Behaviors of Flash-Boiling Jets

Biofuels flash point modelling using neural networks

Experimental study on the application of n-butanol and n-butanol/kerosene blends as fuel for spark ignition aviation piston engine

RP-3 Aviation Kerosene Surrogate Fuel and the Chemical Reaction Kinetic Model

Research on Fuel Spray Characteristics of Coal-Made Fisch-Tropsch Process Diesel/methanol

Application of Neural Network in the Study of Combustion Rate of Natural Gas/diesel Dual Fuel Engine.

Experimental study on spray characteristics of octanol biodiesel and modification of spray tip penetration model

Radial development of pentanol–biodiesel fuel spray in a high-pressure common-rail system

Effects of alcohol fuels on SACI engine and analyze of prediction of SACI engine performance by artificial neural networks

Prediction of emission characteristics of diesel/n-hexanol/graphene oxide blended fuels based on fast outlier detection-sparrow search algorithm-bidirectional recurrent neural network

Application of Elman and Cascade neural network (ENN and CNN) in comparison with adaptive neuro fuzzy inference system (ANFIS) to predict key fuel properties of ABE-diesel blends

Investigation on the ignition delay prediction model of multi-component surrogates based on back propagation (BP) neural network