Abstract:This paper reports a new stick-slip piezoelectric linear actuator with large load density, compact size, and high resolution. It is devised using a dual-arch bridge-type driving mechanism (DBDM) and an integrated elliptical preload mechanism(IEPM). The DBDM can generate a coupling motion on the driving point, which provides clamping and releasing actions during stick-slip motion. Also, the DBDM can magnify the clamping force with large amplification ratios, thus improving driving force and load-carrying capacity. The IEPM uses compact flexure hinges to adjust preload force, reducing structural dimension. Then, theoretical analysis and simulations are conducted, and a prototype is fabricated. A modified driving voltage with smooth turning points is designed to improve motion properties further. Experiments show that load density is 0.037 g/mm $^{\mathbf{3}}$ under the driving voltage of 100 V. The actuator has an overall size of 33.6 mm $\times$ 20 mm $\times$ 8 mm and a displacement resolution of 22 nm. Note to Practitioners —Most research on linear actuators focused on motion displacement improvement, and more research needs to be done on improving load-carrying capacity. Therefore, this paper designs a force amplification linear actuator with a compact structure using the DBDM. In the experimental stage, the sudden change of the driving signal affects the output performance, and a modified sawtooth voltage is used to improve the output speed and load-carrying capacity. The experimental results show that under the modified sawtooth wave voltage, the maximum speed of the slider is 1.4 mm/s, and the speed is increased by 17% compared with the traditional wave. When a 200 g load is applied to the slider, the linear actuator operates at a stable speed of 1.2 $\mu $ m/s, 33% faster than conventional sawtooth waves. As a result, the designed actuator has superior performance at higher loads.

A novel macro-fiber-composite stick-slip actuator with large single-step displacements

Experimental study of axial-compressed macro-fiber composite bimorph with multi-layer parallel actuators for large deformation actuation

A Novel 2-DOF Piezoelectric Stick-Slip Actuator With Parallel Guiding Decoupling

A New Stick-Slip Piezoelectric Actuator Using Dual-Arch Bridge-Type Compliant Mechanisms

Rate-Dependent Hysteresis Modeling and Displacement Tracking Control Based on Least-Squares SVM for Axially Pre-Compressed Macro-Fiber Composite Bimorph.

Experiments and Study of a Low-Frequency, High-Speed Bi-Directional Piezoelectric Stick-Slip Actuator

The dynamics of the hexavalent chromium induced apoptotic patterns in vitro.

A dual-mode stick-slip piezoelectric actuator imitating mantis forefoot

[Clinical characteristics of 8 cases of primary tracheal tumors].

Achieving smooth motion of stick–slip piezoelectric actuator by means of alternate stepping

Design and Position/force Control of an S-shaped MFC Microgripper

A flexure hinged piezoelectric stick–slip actuator with high velocity and linearity for long-stroke nano-positioning

Design and performance evaluation of a stick-slip actuator with Z-shaped beam and two-stage amplification system

Improving Load Capacity of Stick-Slip Actuators in Both Driving Directions Via a Shared Driving Foot

A Gravity-Assisted Piezoelectric Inertial Actuator for Bidirectional Smooth Drives by Single Excitation Source

Development and Hybrid Position/Force Control of a Dual-Drive Macro-Fiber-Composite Microgripper

Design and test of a compact large-stroke dual-drive linear-motion system

Design, Modeling, Testing, and Control of a Novel Fully Flexure-Based Displacement Reduction Mechanism Driven by Voice Coil Motor

A Large-Stroke Reluctance-Actuated Nanopositioner: Compliant Compensator for Enhanced Linearity and Precision Motion Control

A Novel Stick–Slip Piezoelectric Actuator Based on a Triangular Compliant Driving Mechanism

A Novel Stick-Slip Type Rotary Piezoelectric Actuator