Abstract:A new jet fuel surrogate was developed in this work by emulating real jet fuel properties including physical, gas phase chemical properties and threshold sooting index (TSI). An intelligent optimization methodology was proposed to calculate the species composition that inherently satisfies both the physical and chemical characteristics as well as sooting tendency. Eight properties were selected as the target properties for the jet fuel surrogate development, including liquid density, viscosity, surface tension, cetane number (CN), hydrogen carbon (H/C) ratio, molecular weight (MW), lower heating value (LHV) and TSI. As a result, the CN, H/C ratio, LHV, TSI and density of the new jet fuel surrogate are reproduced excellently with very little deviations within 3%. The averaged deviation of viscosity is −6.318% and the deviations of MW is 9.776%. As the highest deviation among all properties, the averaged deviation of surface tension is 11.76%. Based on the newly developed jet fuel surrogate, a skeletal jet fuel surrogate mechanism with 5 components including decalin, n-dodecane, iso-cetane, iso-octane and toluene was developed. The skeletal jet fuel surrogate mechanism was significantly compacted into 74 species and 189 reactions by describing the chemistries for the oxidation of large molecules C4–Cn and small H2/CO/C1 molecules respectively, which makes it practical to be used for 3-D engine combustion simulations. The validations of ignition delay times present reasonable agreement between experiment and predictions over a wide range of equivalence ratios (0.5–2.0) and pressures (8–30 atm), except for a shift of negative temperature coefficient (NTC) region towards higher temperatures at Φ = 1.5, 20 atm: in the simulation the NTC region is from 830 K to 950 K while in the experiment the NTC region is from 740 K to 890 K. The predicted species concentrations can reproduce the trend of the experimental data, especially for O2, CO and CO2. The simulated laminar flame speed at 400 K and 470 K are with absolute averaged deviations of 3.5% and 4.06% respectively. The constant volume spray and combustion validations are reasonably good. In the engine combustion validations, a multistep soot model was embedded into the new jet fuel surrogate mechanism. The predicted in-cylinder pressure can reproduce the experimental data, expect for small deviations after the peak pressure (the averaged deviation is around 6.2% after the peak pressure). The embedded soot model can well reproduce the trend of the experimental data. It can be concluded that this new jet fuel surrogate mechanism is compact and robust for the utilization in diesel engine combustion simulation.

Impacts of Fuel Stage Ratio on the Morphological and Nanostructural Characteristics of Soot Emissions from a Twin Annular Premixing Swirler Combustor

Morphological and nanostructure characteristics of soot particles emitted from a jet-stirred reactor burning aviation fuel

Effects of Na and Fe on the Formation of Coal-Derived Soot in a Two-Stage Flat-Flame Burner

Ultrafine Particle Formation in Pulverized Coal, Biomass, and Waste Combustion: Understanding the Relationship with Flame Synthesis Process

Numerical Study of Soot Particles from Low Temperature Combustion of Engine Fueled with Diesel Fuel and Unsaturation Biodiesel Fuels

Role of Dimethyl Ether in Incipient Soot Formation in Premixed Ethylene Flames

Experimental and simulation studies on flame characteristics and soot formation of C2H2 jet flames

Morphology and Fractal Dimension of Size-Resolved Soot Particles Emitted from Combustion Sources

Aircraft soot from conventional fuels and biofuels during ground idle and climb-out conditions: Electron microscopy and X-ray micro-spectroscopy

Morphology, Composition, and Mixing State of Primary Particles from Combustion Sources — Crop Residue, Wood, and Solid Waste

Development of a New Jet Fuel Surrogate and Its Associated Reaction Mechanism Coupled with a Multistep Soot Model for Diesel Engine Combustion

Impact of Dilution Ratio and Burning Conditions on the Number Size Distribution and Size-Dependent Mixing State of Primary Particles from Domestic Solid Fuel Burning

Microphysical Properties of Atmospheric Soot and Organic Particles: Measurements, Modeling, and Impacts

Soot Formation and Its Effect in an Aero Gas Turbine Combustor

Effects of adding n-amyl alcohol, dimethylfuran to fuel on soot formation in aviation kerosene diffusion flame

Soot Morphology and Nanostructure Differences between Chinese Aviation Kerosene and Algae-Based Aviation Biofuel in Free Jet Laminar Diffusion Flames

Investigations On Mechanism Of Soot Formation During Combustion And Control Of Soot Emission

Effects of Fuel Structure on Structural Characteristics of Soot Aggregates

Structure and Behavior of Soot in Pulverized-Coal Flame

Combustion and Particulate I/SVOC Characteristics of an Aero-engine Combustor with Dual-Stage under Operational Power and Injection Pressure

The Evolution of Soot Morphology and Nanostructure in Laminar Diffusion Flame of Surrogate Fuels for Diesel