Abstract:In this study, one of the commonly used MXene (Ti3C2Tx) and β nucleated isotactic polypropylene (β-iPP)/MXene composites of different compositions were fabricated. The effects of MXene on non-isothermal crystallization and polymorphic behavior of β-iPP/MXene composites were comparatively studied. The non-isothermal crystallization kinetics indicates that for all samples, the lower cooling rates promote composites to crystallize at higher temperatures. When MXene and β-Nucleating agent (β-NA) are added separately, the crystallization temperature of composites shifts towards higher temperatures at all cooling rates. When MXene and β-NA are added simultaneously, the composite shows different cooling rate dependence, and the effects of improving crystallization temperatures is more obvious under rapid cooling. The activation energy of four samples iPP, iPP/MXene, iPP/β-NA, and iPP/MXene/β-NA were −167.5, −185.5, −233.8, and −218.1 kJ/mol respectively, which agree with the variation tendency of crystallization temperatures. The polymorphic behavior analysis obtained from Differential Scanning calorimetry (DSC) is affected by two factors: the ability to form β-crystals and the thermal stability of β-crystals. Because β-crystals tend to recrystallize to α-crystals below a critical temperature, to eliminate the effect of β-α recrystallization, the melting curves at end temperatures Tend = 50 °C and Tend = 100 °C are comparatively studied. The results show that more thermally unstable β-crystals would participate in β-α recrystallization with higher cooling rates. Moreover, thermal stability of β-crystals is improved by adding MXene. To further verify these findings, samples of three different thermal conditions were synthesized and analyzed by DSC, X-Ray Diffraction (XRD), and Polarized Light Optical Microscopy (PLOM), and the results were consistent with the above findings. New understandings of synthesizing β-iPP/MXene composites with adjustable morphologies and polymorphic behavior were proposed.

Dynamical mechanical and impact strength behavior of 3D‐printing testing specimens manufactured by fused filament fabrication of isotactic polypropylene/functionalized titania nanotubes nanocomposites: Influence of β‐crystal promoting

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Exploring the Effects of MXene on Nonisothermal Crystallization and Melting Behavior of Β-Nucleated Isotactic Polypropylene

3D printing polypropylene composites reinforced with functionalized halloysite: Balance between stiffness and impact resistance

Optimizing titanium carbide (TiC) ceramic nanofiller loading in isotactic Polypropylene for MEX additive manufacturing: Mechano-thermal and rheology aspects

Effect of Carbon Nanotube on Thermal, Tribological and Mechanical Properties of 3D Printing Polyphenylene Sulfide

Water-mediated chelation dynamics of dicarboxylic acid functionalized TiO2 nanoparticles for β-nucleation enhancement in isotactic polypropylene composites

Development of isotactic polypropylene‐based 3D printing materials with good dimensional accuracy and excellent impact properties

Influence of Surface-Modified TiO2 Nanoparticles on Fracture Behavior of Injection Molded Polypropylene

On the substantial mechanical reinforcement of Polylactic Acid with Titanium Nitride ceramic nanofillers in material extrusion 3D printing

Studying the influence of the addition of nano-titanium dioxide on the rheological, mechanical, thermal, and electrical properties of polycarbonate/wood flour

On the Mechanical Response of Silicon Dioxide Nanofiller Concentration on Fused Filament Fabrication 3D Printed Isotactic Polypropylene Nanocomposites

Effects Of Beta-Nucleating Agent And Crystallization Conditions On The Crystallization Behavior And Polymorphic Composition Of Isotactic Polypropylene/Multi-Walled Carbon Nanotubes Composites

Optimization of Isotactic Polypropylene Nanocomposite Content of Tungsten Carbide for Material Extrusion 3D Printing

Optimization Course of Titanium Nitride Nanofiller Loading in High-Density Polyethylene: Interpretation of Reinforcement Effects and Performance in Material Extrusion 3D Printing

The impact of the glass microparticles features on the engineering response of isotactic polypropylene in material extrusion 3D printing

High Performance Polycarbonate Nanocomposites Mechanically Boosted with Titanium Carbide in Material Extrusion Additive Manufacturing

Thermal and Mechanical Properties of Reprocessed Polylactide/Titanium Dioxide Nanocomposites for Material Extrusion Additive Manufacturing

Highly Tough Yet Stiff, Transparent, and Recyclable PMMA Nanocomposites Incorporating TPU Nanofibril Networks with High Thermal Stability and Strong Interfacial Adhesion

Thermal and Mechanical Characterization of the New Functional Composites Used for 3D Printing of Static Mixers

Effect of the β-crystal formation in isotactic polypropylene used for eco-friendly insulating material