Abstract:The results of studying the influence of mechanical alloying (MA) on the surface morphology, microstructure, and atomic–crystalline structure of particles of the Fe–Cr–Co–Ni–Mn multicomponent powder mixture are presented. The initial components are as follows: the R-10 radio-engineering carbonyl iron powder with average particle size d = 3.5 μm, the NPE-1 nickel powder with d = 150 μm, the PK-1u cobalt powder with d < 71 μm, the PKh-1M chromium powder with d < 125 μm, and the MR0 manganese powder with d < 400 μm. The MA of the prepared mixture was performed in an AGO-2 water-cooled mechanical activator using 9-mm steel balls with an acceleration of 90 g in air. The alloying time varies from 5 to 90 min. The ratio of the ball weight to the mixture weight is 20 : 1. X-ray diffraction patterns of the initial and alloyed mixtures, as well as of the sample formed by sintering, are recorded using a DRON 3M diffractometer in Fe K α radiation at 2θ = 30–100°. The microstructure of the mixture particles and the compact sample metallographic specimen after sintering are investigated by scanning electron microscopy. It is established that the peaks of initial components are absent in the X-ray diffraction pattern after mechanical activation for 90 min, and peaks corresponding to the phase representing the γ-Fe-based solid solution having a face-centered crystal lattice are presented. Herewith, the fraction of the amorphous phase increases to 20%. A compact single-phase material is formed from the mixture prepared after 90-min alloying by spark plasma sintering at 800°C for 10 min. Its density is 7.49 kg/cm 3 , resistivity is 0.94–0.96 × 10 –6 Ω m, and microhardness is 306–328 kg/mm 2 . The phase is uniformly distributed over the volume.

Microstructure evolution and magnetic characteristics of a novel high entropy alloy produced by mechanical alloying and spark plasma sintering

Microstructure and mechanical properties of a high entropy alloy with a eutectic composition (AlCoCrFeNi2.1) synthesized by mechanical alloying and spark plasma sintering

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Microstructure and Magnetic Characteristics of AlCrCuFeNiTi High-Entropy Alloy Prepared by Mechanical Alloying Followed by Spark Plasma Sintering

Evolution from Amorphous to Nanocrystalline and Corresponding Magnetic Properties of Fe-Si-B-Cu-Nb Alloys by Melt Spinning and Spark Plasma Sintering

Microstructure and Mechanical Properties of Novel CrCoNi–Al2O3P Medium Entropy Alloy-Matrix Composites

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Microstructure, deformation behavior, and dynamic recrystallization kinetics of FeNiMnCu-based high entropy alloys prepared by mechanical alloying and spark plasma sintering

Effect of Tungsten on Microstructure and Mechanical Properties of Novel NiMnCrMoWx High-Entropy Alloys Developed by Mechanical Alloying

Microstructure evolution and mechanical properties of aluminium matrix composites reinforced with CoMoMnNiV high-entropy alloy

Microstructure and Phase Composition of the Cr-Mn-Fe-Co-Ni High-Entropy Alloy Obtained by Wire-Arc Additive Manufacturing

Mechanical Alloying with the Partial Amorphization of the Fe–Cr–Co–Ni–Mn Multicomponent Powder Mixture and Its Spark Plasma Sintering to Produce a Compact High-Entropy Material

Phase Evolution and Mechanical Properties of AlCoCrFeNiSix High-Entropy Alloys Synthesized by Mechanical Alloying and Spark Plasma Sintering

Influence of mechanical alloying on structural, thermal, and magnetic properties of Fe50Ni10Co10Ti10B20 high entropy soft magnetic alloy

The Influence of Ball Milling Time and Sintering Temperature on the Structural and Capabilities of FeCoCrNiMn High-Entropy Alloy

Properties of High-Entropy Fe30Co20Ni20Mn20Al10 Alloy Produced by High-Energy Ball Milling

Processing and Characterization of a Mechanically Alloyed and Hot Press Sintered High Entropy Alloy from the Al-Cr-Fe-Mn-Mo Family

Structure and properties of Fe40Mn20Cr20Ti10Al10 high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

Analyzing the Phase evolution, Microstructure and Wear Response of Spark Plasma Sintered Al0.5CoCrFeNi2 High Entropy Superalloy

Magnetic, Structural and Mechanical Behavior of Transitional Bulk Nanostructured Al Alloy

Microstructural and Magnetic Characteristics of High-Entropy FeCoNiMnTi Alloy Produced via Mechanical Alloying