Abstract:Advances in Structural Engineering, Ahead of Print. The rotation of beam and column components is a key parameter in structural health monitoring (SHM), which providing analysis of bending deformation, evaluation of structural stability, and overall structural performance. Conventional sensors directly measuring rotation are typically designed assuming linear behavior. It becomes challenging to achieve precise and rapid measurements of small deformations while accurately measuring significant large deformations. This study obtained experimental and analytical studies to identify the rotation response of flexural structures using long-gauge fiber optical sensor array. Rotation is determined through two mechanisms: the plane section assumption, utilizing strain distributions on the compression and tension sides, and the sectional fiber model (SFM)-based neutral axis identification. In order to discuss the applicability of these two mechanisms from elastic to plastic state, four identification methods are proposed: Method 1 uses strain distribution on the concrete surface to identify rotation, Method 2 uses strain on steel bars, and Methods 3 and 4 use SFM-based neutral axis identification with strain measured on the compression side concrete surface and tension side steel reinforcements, respectively. Laboratory tests of beams and columns as well as field tests were shown. First, a comparison of the rotation identification accuracy among the four methods was conducted using a reinforced concrete (RC) beam test in the elastic state. Results showed good agreement between the rotations identified by all four methods and those directly measured by the tilt meter. And then, the accuracy of rotation identification in crack state and inelastic state was discussed by using a RC column test. The results indicate that, following the occurrence of cracks in concrete surface, neither Method 1 nor Method 2 can accurately identify the rotation. This is attributed to the fact that cracks disrupt the correspondence between the strain on the tension side and the compression side. Meanwhile, Methods 3 and 4 maintain a good rotational identification accuracy even after cracks happened. Moreover, when the steel reinforcement undergoes yielding and the concrete column enters the inelastic state, the rotation results identified by Methods 3 and 4 still match with the directly measured rotations. This underscores the effectiveness of the SFM-based rotational identification under large deformation conditions. Furthermore, experimental results indicate that with the increase in deformations, slip occurred in the sensing units near the column base in the sensor array on the tension side. This shows that the sensing units installed on the steel reinforcement (Method 4) are more suitable for calculating rotations during the large deformation state compared to the sensing units positioned on the concrete surface (Method 3). At last, two case studies involving the monitoring of an actual bridge grid and a bridge column were investigated to assess the effectiveness of dynamic rotation identifications. The performance evaluation results for various rotation angle measurement sensors demonstrate that long-gauge fiber optical sensors can be used for rotation identification, ensuring the stability of dynamic rotation identification.

Inclination information-aided circumferential deformation reconstruction error correction method for CFRP belt integrated with optical fiber sensor

Theory And Error Compensation Method Based On The Tilt Sensor Adopted In Dynamic Angle Measurement Of The Fiber Optic Gyroscope

Online Path Correction under End Point Nonholonomic Constraints – Implementation with Visual Sensing in Robotic Fiber Placement

Kinematic Modeling and Parameter Identification for a Heavy Gantry-Type Automated Fiber Placement Machine Considering Gravity Deformation

A Modeling and Calibration Method of Heavy-Duty Automated Fiber Placement Robot Considering Compliance and Joint-Dependent Errors

Measurement of deformed surface and key data processing based on reverse engineering

Deformation measurement based on high resolution distributed optical fiber sensing and conjugated beam method

Cross Section Deformation Correction of Flexible Tentacle Shape Based on Fiber Bragg Grating

FOSS-Based Method for Thin-Walled Structure Deformation Perception and Shape Reconstruction

Computer-aided feature recognition of CFRP plates based on real-time strain fields reflected from FBG measured signals

Research on Deformation Reconstruction Based on Structural Curvature of CFRP Propeller With Fiber Bragg Grating Sensor Network

Accurate rotation identification of flexural structures using long-gauge fiber optical sensors

Detection of Slip for CFRP-concrete Interface Using Stereovision Method Corrected by Epipolar Constraint

Effective Optical Fiber Sensing Method for Stiffened Aircraft Structure in Nonlocal Displacement Framework

Design and Optimization of FBG Implantable Flexible Morphological Sensor to Realize the Intellisense for Displacement

Discontinuous Deformation Monitoring of Smart Aerospace Structures Based on Hybrid Reconstruction Strategy and Fiber Bragg Grating

Deformation Monitoring and Shape Reconstruction of Flexible Planer Structures Based on FBG

Three-Dimensional Mapping Technology for Structural Deformation during Aircraft Assembly Process

Interface Transferring Mechanism and Error Modification of FRP-OFBG Strain Sensor Based on Standard Linear Viscoelastic Model

Calibration of Coherent Optical Fiber Bundle with Lcd Screen for Deformation Measurements

A modeling and calibrating method of FBG sensors for wing deformation displacement measurement