Abstract:Fused Deposition Modeling (FDM) is a well-established manufacturing method for producing both prototype and functional components. This study investigates the mechanical properties of FDM components by material and process-related influencing variables. Tensile tests were conducted on seven different materials in their raw filament form, two of which were fiber-reinforced, to analyze their material-related influence. To cover a wide range from standard to advanced materials relevant for load-carrying components as well as their respective variations, polylactic acid (PLA), 30% wood-fiber-reinforced PLA, acrylonitrile butadiene styrene (ABS), polycarbonate (PC), a blend of ABS and PC, Nylon, and 30% glass-fiber-reinforced Nylon were selected. The process-related influencing variables were studied using the following process parameters: layer thickness, nozzle diameter, build orientation, nozzle temperature, infill density and pattern, and raster angle. The first test series revealed that the addition of wood fibers significantly worsened the mechanical behavior of PLA due to the lack of fiber bonding to the matrix and significant pore formation. The polymer blend of ABS and PC only showed improvements in stiffness. Significant strength and stiffness improvements were found by embedding glass fibers in Nylon, despite partially poor fiber–matrix bonding. The materials with the best properties were selected for the process parameter analysis. When examining the impact of layer thickness on part strength, a clear correlation was evident. Smaller layer thicknesses resulted in higher strength, while stiffness did not appear to be affected. Conversely, larger nozzle diameters and lower nozzle temperatures only positively impacted stiffness, with little effect on strength. The part orientation did alter the fracture behavior of the test specimens. Although an on-edge orientation resulted in higher stiffness, it failed at lower stresses. Higher infill densities and infill patterns aligned with the load direction led to the best mechanical results. The raster angle had a significant impact on the behavior of the printed bodies. An alternating raster angle resulted in lower strengths and stiffness compared to a unidirectional raster angle. However, it also caused significant stretching due to the rotation of the beads.

Material testing for injection molded and 3D printed pristine/glass reinforced nylon at various strain rates

High Strain Rate Mechanical Behavior of Polyamide 66 and Polyamide 66-Glass Fiber Reinforced

Impact of strain rate on mechanical properties of polylatic acid fabricated by fusion deposition modeling

Manufacturing Process Effect on the Mechanical Properties of Glass Fiber/Polypropylene Composite Under High Strain Rate Loading: Woven (W-GF-PP) and Compressed GF50-PP

Effect of Strain Rate on the Transverse Tension and Compression Behavior of a Unidirectional Non-Crimp Fabric Carbon Fiber/Snap-Cure Epoxy Composite

Experimental Study Of In-Plane Mechanical Performance Of Carbon/Glass Hybrid Woven Composite At Different Strain Rates

Mechanical Properties of Raw Filaments and Printed Specimens: Effects of Fiber Reinforcements and Process Parameters

Strain rate dependence of 3D printed continuous fiber reinforced composites

A Coherent Assessment of the Compressive Strain Rate Response of PC, PETG, PMMA, and TPU Thermoplastics in MEX Additive Manufacturing

Fiber Orientation and Strain Rate-Dependent Tensile and Compressive Behavior of Injection Molded Polyamide-6 Reinforced with 20% Short Carbon Fiber

Design and optimization methodology for different 3D processed materials (PLA, ABS and carbon fiber reinforced nylon PA12) subjected to static and dynamic loads

Evaluation of Tensile properties of FRP Composite Laminates under Varying Strain Rates and Temperatures

Effect of post-heat treatment on the mechanical and surface properties of nylon 12 produced via material extrusion and selective laser sintering processes

Temperature and strain rate-dependent compression properties of 3D-printed PLA: an experimental and modeling analysis

Effect of process parameters on mechanical and tribological characteristics of FDM printed glass fiber reinforced PLA composites

Experimental Investigation of the Effect of Strain Rate on the Compression Behavior of 3d E-Glass Fiber-Reinforced Composites

Experimental investigation on in-plane shear behavior of E-glass fiber/epoxy laminated composites under different strain rates

An Examination of the Low Strain Rate Sensitivity of Additively Manufactured Polymer, Composite and Metallic Honeycomb Structures

Analysis of tensile behavior of Nylon-CF fabricated using material extrusion

High Strain Rate Yielding of Additive Manufacturing Inconel 625 by Selective Laser Melting

Investigation of strain rate dependent microscopic failure mechanisms in short fiber reinforced plastics using finite element simulations