Abstract:Charge accumulation and charged defects at both bulk and buried heterojunction interfaces of perovskites are primarily related to the photovoltaic performance and shelf stability of perovskite solar cells (PSCs). Moreover, detrimental defects distributing along the perovskite bottom side in contact with the tin oxide (SnO2) surface may exert unparalleled significance in charge extraction and transport. Most importantly, interfacial nonradiative recombination can also widely exist, which will seriously hamper efficiency of the related device. In this work, a multifunctional chemical bridge at the perovskite/SnO2 interface is devised through triggering an in situ polymerization strategy, by which cross-linked polymerizable 3-(trimethoxysilyl)propyl methacrylate (MAPS) monomers under the combination of temperature and initiators can form bulkier macropolymers (MAPS dimers). Detailed theoretical and experimental results reveal that the carbonyl groups (CO) of both MAPS monomers and MAPS dimers can chemically anchor to perovskite bottom side through a CO···Pb coordination bond interaction to regulate the film quality and the siloxane groups effectively couple with oxygen vacancies on the SnO2 film surface to facilitate its optoelectronic properties. Compared with the primitive MAPS monomer units, the resultant MAPS dimers simultaneously prevent interfacial charge accumulation and demonstrate a more benign energy level alignment to further augment photovoltaic performance of PSCs. Thus, the devices assembled under open-air conditions based on double-sided passivation deliver a decent photoelectronic performance with the champion efficiency of 20.94% accompanied by negligible hysteresis. Meanwhile, the unencapsulated targeted devices maintain 93.1% and 86.5% of their original efficiency after continuous 500 h thermal treatment and 500 h light illumination under open-circuit conditions, respectively.

Spontaneous Internal Encapsulation via Dual Interfacial Perovskite Heterojunction Enables Highly Efficient and Stable Perovskite Solar Cells

Internal Encapsulation for Lead Halide Perovskite Films for Efficient and Very Stable Solar Cells

Internal Encapsulation Enables Efficient and Stable Perovskite Solar Cells

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells

Double Perovskite Interlayer Stabilized Highly Efficient Perovskite Solar Cells

In Situ Reconstruction of Hole‐Selective Perovskite Heterojunction with Graded Energetics Toward Highly Efficient and Stable Solar Cells

Highly efficient and stable perovskite solar cells enabled by low-dimensional perovskitoids

In Situ Polymerizing Internal Encapsulation Strategy Enables Stable Perovskite Solar Cells toward Lead Leakage Suppression

Oligomeric Silica-Wrapped Perovskites Enable Synchronous Defect Passivation and Grain Stabilization for Efficient and Stable Perovskite Photovoltaics

Stabilization of highly efficient perovskite solar cells with a tailored supramolecular interface

Surface Terminated 3D/2D Heterojunction Enables Efficient and Stable Perovskite Solar Cells

Synchronous Elimination of Excess Photoinstable PbI2 and Interfacial Band Mismatch for Efficient and Stable Perovskite Solar Cells

High‐Performance CsPbIxBr3‐x All‐Inorganic Perovskite Solar Cells with Efficiency over 18% Via Spontaneous Interfacial Manipulation

In Situ Dual‐Interface Passivation Strategy Enables The Efficiency of Formamidinium Perovskite Solar Cells Over 25%

2D/3D heterojunction engineering at the buried interface towards high-performance inverted methylammonium-free perovskite solar cells

Impeded Degradation of Perovskite Solar Cells Via the Dual Interfacial Modification of Siloxane

Visualizing Interfacial Energy Offset and Defects in Efficient 2D/3D Heterojunction Perovskite Solar Cells and Modules

Internal Encapsulation Strategy Using a Polymer Enables Efficient, Stable, and Lead‐Safe Inverted Perovskite Solar Cells

Stability-enhanced perovskite heterointerfaces and solar cells via strongly anchored and sterically hindered ligands

Synchronous Modulation of Defects and Buried Interfaces for Highly Efficient Inverted Perovskite Solar Cells

Poly(3‐hexylthiophene)/perovskite Heterointerface by Spinodal Decomposition Enabling Efficient and Stable Perovskite Solar Cells