Abstract:The lithium-ion battery has the advantages of high energy density, long service life, and good safety performance, and is used as an ideal energy storage device. Cobalt-free lithium-rich manganese cathode materials have attracted much attention due to their high specific capacity and low cost. However, its poor cycling performance is not conducive to practical application. So far, researchers have mainly addressed this problem with surface coatings. In this study, spinel Li4Mn5O12 was successfully prepared by wet chemical method to modify the surface of Li1.2Ni0.2Mn0.6O2. The X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) test results showed that the crystal structure of the samples did not change significantly, but the cationic order was improved. The results of the scanning electron microscope (SEM), energy dispersive spectrometer (EDS), and transmission electron microscope (TEM) showed that an ultrathin spinel Li4Mn5O12 surface-modified layer with a thickness of about 10 nm was successfully constructed on the raw material surface. In addition, the lithium-ion diffusion coefficients (DLi+) of the raw materials and modified materials were calculated by electrochemical impedance spectroscopy (EIS) test and impedance fitting. The results indicated that the ultrathin Li4Mn5O12 surface modification shell can increase the lithium-ion diffusion rate of the material and improve the rate capability of the material. So, the results show that the surface modification layer of spinel Li4Mn5O12 can reduce the oxygen loss of the first cycle and improve the cationic order of the material. Therefore, the first coulombic efficiency of Li4Mn5O12/Li1.2Ni0.2Mn0.6O2 material at the current density of 12.5 mA×g-1 reaches 80.46%, and the capacity retention rate reaches 91.74% after 50 cycles, which is 3.36% and 21.23% higher than that of the raw materials, respectively. It showed better electrochemical reversibility and cyclic stability. This study provides a straightforward and convenient modification method for improving the stability of cobalt-free lithium-rich manganese cathode materials and has a favorable application prospect.

Interfacial cerium modification promotes the electrochemical properties of self-assembled Li1.2Mn0.54Ni0.13Co0.13O2 hollow microspheres

Na Doping and CeO2 Nanoparticle Surface Modification Enhancing the Li-Rich Li1.2Mn0.54Ni0.13Co0.13O2 Cathode Material for a Lithium-Ion Battery

Interphase Modification of Li(Ni0.5Co0.2Mn0.3)O2 Based Lithium Battery Electrode Materials by Depolarized and Pre-Lithiation for High Capacity and Cycling Performance

Surface Modification Driven Initial Coulombic Efficiency and Rate Performance Enhancement of Li1.2Mn0.54Ni0.13Co0.13O2 Cathode

Simultaneous dual modification of Li-rich Mn-based cathode in restraining oxygen release and structure distortion

Enhanced electrochemical performances of cerium-doped Li-Rich Li1.2Ni0.13Co0.13Mn0.54O2 cathode materials

Effect of Cerium Substitution on Structural and Electrochemical Performance of Li[Li0.2Mn0.54Co0.13Ni0.13]O2 Cathode Material for Lithium-Ion Battery

Collaboratively enhancing electrochemical properties of LiNi0.83Co0.11Mn0.06O2 through doping and coating of quadrivalent elements

Enhancing Performances of Co-free Li-rich Mn-based Layered Cathode Materials Via Interface Modification of Multiple-Functional Mn3O4 Shell

Invoking Interfacial Engineering Boosts Structural Stability Empowering Exceptional Cyclability of Ni‐Rich Cathode

Building interface bonding and shield for stable Li-rich Mn-based oxide cathode

Enhanced electrochemical performance of Ni-rich layered LiNi0.9Co0.05Mn0.05O2 cathode material via synergistic modification of cerium doping and ceria coating

Improving the Electrochemical Performance of Li-rich Li1.2Ni0.2Mn0.6O2 by Using Ni-Mn Oxide Surface Modification

Enhanced structurally stable cathodes by surface and grain boundary tailoring of Ni-Rich material with molybdenum trioxide

Mg2+ Doped LiNi1/3Co1/3Mn1/3O2 Hollow Flake-Like Structures with Enhanced Performances Cathodes for Lithium-Ion Batteries

Improved High Rate Capability of Li[Li0.2Mn0.534Co0.133Ni0.133]O2 Cathode Material by Surface Modification with Co3O4

AlPO4-Li3PO4 Dual Shell for Enhancing Interfacial Stability of Co-free Li-rich Mn-based Cathode

Enhanced interfacial reaction interface stability of Ni-rich cathode materials by fabricating dual-modified layer coating for lithium-ion batteries

Preparation of CeO2-coated Li1.2Mn0.54Co0.13Ni0.13O2 as cathode materials for Lithium Ion Batteries

Buliding Ultrathin Li4mn5o12 Shell for Enhancing the Stability of Cobalt-Free Lithium-Rich Manganese Cathode Materials

One-pot synthesis and multifunctional surface modification of lithium-rich manganese-based cathode for enhanced structural stability and low-temperature performance