Abstract:Signal to noise ratios (SNR) in magnetic resonance microscopy images are limited by acquisition times and the decreasing number of spins in smaller voxels. Significant SNR gains from cooling of the RF receiver are only realized when the Johnson noise generated within the RF hardware is large compared to the electromagnetic noise produced by the sample. Cryogenic cooling of imaging probes is common in high field systems but proves difficult to insulate the sample from extreme temperatures. We designed a chamber to cool only the tune and match circuitry to show it is possible to achieve much of the available SNR gain available for cooled coils. We designed a microcoil circuit to resonate at 650 MHz for imaging on a 15.2 T scanner. Surface loops and solenoids of varying diameters were tested to determine the largest diameter coil that demonstrated significant SNR gains from cooling. A liquid N2 cryochamber was designed to cool the circuitry while leaving the RF coil in ambient air. As the cryochamber was filled with liquid N2, Q-factors were measured on the bench while monitoring the coil's surface temperature. Improvements of SNR on images of solutions were demonstrated via cooling the tune and match circuit in the magnet bore. At 650 MHz, loops and solenoids < 3 mm in diameter showed significant improvements in quality factor on the bench. The resistance of the variable capacitors and the coaxial cable were measured to be 45% and 32% of room temperature values near the Larmor frequency. Images obtained with a 2 turn, 3 mm diameter loop with the matching circuit at room temperature and then cooled with liquid nitrogen demonstrated SNR improvements of a factor of 2. By cooling the tune and match circuit and leaving the surface loop in ambient air, SNR was improved by a factor of 2. The results are significant because it allows for more space to insulate the sample from extreme temperatures.

Solid cryogen: a cooling system for future MgB2 MRI magnet

Research on Stability of ${\rm MgB}_{2}$ Superconducting Magnet for MRI

Conceptual Design of a Portable, Solid-Nitrogen-Cooled 0.5-T/560-mm Point-of-Care MRI Magnet

Magnetic, Mechanical and Thermal Modeling of Superconducting, Whole-body, Actively Shielded, 3 T MRI Magnets Wound Using MgB2 Strands for Liquid Cryogen Free Operation

A Persistent-Mode 0.5 T Solid-Nitrogen-cooled MgB2 Magnet for MRI.

A Persistent-Mode 0.5t Solid-Nitrogen-Cooled Mgb2 Magnet for Mri

Superconducting joints using reacted multifilament MgB 2 wires: A technology toward cryogen-free MRI magnets

Thermal Analysis of the 4 K Cryostat Within a 1.5 T Conduction-Cooled Superconducting Magnet for Whole-body MRI Application

A Cryogenic Tune and Match Circuit for Magnetic Resonance Microscopy at 15.2T

Magnetic and Cryogenic Design of MICE Coupling Solenoid Magnet System

Thermal studies on cryocooler thermal masses from 4 K to 300 K for MRI applications

Design of a 30-K/4-kj HTS Magnet Cryocooled with Solid Nitrogen

A 30 Kj Bi2223 High Temperature Superconducting Magnet for SMES with Solid-Nitrogen Protection

A Superconducting Magnet System for Whole-Body Metabolism Imaging

Development of Large-Bore Superconducting Magnet

A Superconducting Magnet with Center Field of 10 T and Φ100 Mm Warm Bore

Thermal analysis of a 3 T cryogen-free superconducting magnet for electromagnetic property measurement system

First-Cut Design of a Benchtop Cryogen-Free 23.5-T/25-mm Magnet for 1-GHz Microcoil NMR

Conduction-Coolled HTS Magnets Closed-Loop System Excited by a Rotating Magnets Flux Pump

A Cryogen Recondensing Cooling System for Scientific Experiment in the Pulsed High Magnetic Field

FABRICATION OF A CONDUCTION COOLED SUPERCONDUCTING MAGNET FOR THE SOLIDIFICATION OF HIGH-ENTROPY ALLOYS