Abstract:Nowadays, anodized coating on additively manufactured (AM) or 3D printed Al-10Si-Mg alloy are used for various components in spacecraft such as antenna feeds, wave guides, structural brackets, collimators, thermal radiators etc. In this study, Artificial Neural Network (ANN) and Power law-based models are developed from experimental nanoindentation data for predicting elastic modulus and hardness of anodized AM Al-10Si-Mg at any desired loads. Data from nanoindentation experiments conducted on plan- and cross-sections of anodized coating on AM Al-10Si-Mg alloy was considered for modelling. Apart from nanomechanical properties, load and displacement curves were predicted using Python software from ANN and the Power law model of nanoindentation. It is observed that the ANN model of 50 mN nanoindentation experimental data can accurately predict the loading pattern at any desired load below 50 mN. Elastic modulus and hardness of anodized AM Al-10Si-Mg computed from ANN and the power law model of the unloading curve are also comparable with the values obtained from Weibull distribution analysis reported elsewhere. The derived models were also used to predict nanomechanical properties at 25 and 35 mN, for which no experimental data was available. The computed hardness of plan section of the anodic coating is 3.99 and 4.02 GPa for 25 and 35 mN, respectively. The computed hardness of cross-section of the anodic coating of is 7.16 and 6.61 GPa for 25 and 35 mN, respectively. Thus, the ANN and Power law model of nanoindentation can predict elastic modulus and hardness at different loads by conducting the minimum number of experiments. The novel approach to predict nanomechanical properties using ANN resulted in determining realistic and design specific data on hardness and modulus of the anodized coating on AM Al-10Si-Mg alloy.

Use of Artificial Neural Network Models to Predict Coated Component Life from Short-Term Electrochemical Impedance Spectroscopy Measurements

Prediction of the Property of Corrosion Resistance of A Surface Alloyed Layer by Using Artificial Neural Networks

Application of artificial neural networks throughout the entire life cycle of coatings: A comprehensive review

Modelling of Behavior for Inhibition Corrosion of Bronze Using Artificial Neural Network (ANN)

Modeling and optimization of the corrosion resistance of Cr-free and Cr-based chemical conversion coatings on nickel foil by artificial neural network and response surface method

Artificial Neural Network-based approach for prediction of nanomechanical properties of anodic coating on additively manufactured Al-10Si-Mg alloy

Optimization of CED dry film thickness using artificial neural network for automobile industries

Data-driven pitting evolution prediction for corrosion-resistant alloys by time-series analysis

Application of machine learning in predicting pitting corrosion – electrochemical data around the open circuit potential

Prediction and parametric effect of electrical discharge layering of AZ31B magnesium alloy using response surface methodology-assisted artificial neural network

Machine learning prediction of microhardness and corrosion current density of Ni-Co alloys produced by scanning jet electrodeposition

Model-based reinforcement corrosion prediction: Continuous calibration with Bayesian optimization and corrosion wire sensor data

Modeling and Analysis of Copper, Iron, and Cobalt Recovery in a Hybrid Sulfuric Acid–Sodium Chloride Media Using Artificial Neural Network

Data Mining Model for Prediction Effect of Corrosion Inhibition

The use of artificial intelligence combiners for modeling steel pitting risk and corrosion rate

Towards the automated interpretation of impedance spectra from organic coatings using neural networks

Artificial neural network-based prediction model of residual stress and hardness of nickel-based alloys for UNSM parameters optimization

Predicting Sodium-Ion Battery Performance through Surface Chemistry Analysis and Textural Properties of Functionalized Hard Carbons Using AI

"Crypton 1.0": Accurate Cyclic Voltammetry Forecasting of Activated Carbon Electrode with Machine Learning

An artificial neural network method for probabilistic life prediction of corroded reinforced concrete

The Application of Artificial Neural Network Model to Predicting the Acid Mine Drainage from Long-Term Lab Scale Kinetic Test