Abstract:Conventionally assembled monolithic concrete frame structures achieve structural ductility through beam-end failure, which results in structures that are difficult to repair after an earthquake. To improve the seismic and resilience performance, a prefabricated concrete beam–column joint with replaceable graded-yielding energy-dissipating connectors (RGECs) is introduced. The connectors assembled on the upper and lower sides of the beam end dissipate energy and transfer the beam-end load with the steel hinge device. By adjusting the design bearing-capacity coefficient of RGECs to precast beams, the plasticity and damage of the structure can be centered on the core energy-dissipation bending–shear components (BSCs) and buckling segment (BS) of the RGEC, and the structural function can be quickly recovered by replacing only the damaged RGECs after a seismic disaster. Moreover, compared to the conventional joints, the joint with RGEC can achieve target seismic-performance goals at different seismic-risk levels by designing BSCs and BS with graded yielding. Low-cyclic-loading tests were performed on seven full-scale beam–column joint specimens to investigate the effects of different core energy-dissipating member thicknesses, beam reinforcement ratios and loading protocols on the seismic behavior of the proposed joint. Subsequently, the damaged RGECs were replaced, and the structural-function resilience performance was evaluated in terms of the function-recovery efficiency and quality, indicated by the hysteresis response, strain development, and component energy dissipation. The experimental results proved that the beam–column joint exhibited excellent seismic performance and could realize graded-yielding energy dissipation. The damage to the specimens was concentrated in the RGECs, the key members (beams and columns) were in an elastic state, and the energy dissipation ratio of the RGEC was more than 97 %. This enables the rapid recovery of function after earthquakes. After replacing the RGEC, the hysteresis response, strain development, and component energy dissipation of the specimens were consistent with those of the initial specimens. Compared with the original specimen, the difference in each seismic index of the replaced specimen was less than 10 %. Additionally, the structural function recovered quickly, and the resilient performance was good.

Development of a double-stage-yield dissipative beam-to-column joint: Experimental study and application for structural response control

EXPERIMENTAL STUDY ON THE SEISMIC BEHAVIOR OF CFST RECTANGULAR COLUMN TO H-SECTION STEEL BEAM CONNECTIONS WITH EXTERNAL STIFFENERS

Development of design method for precast concrete frame with dry-connected rotational friction dissipative beam-to-column joints

A precast beam-column joint using an innovative friction damper as a connector: Experimental and numerical study

Numerical simulation and seismic performance analysis of sacrificial-energy dissipation beam-column joint

STUDIES ON THE ASEISMIC PERFORMANCE OF HIGH RISE STEEL STRUCTURES WITH NEW BEAM-COLUMN JOINTS DISSIPATING SEISMIC ENERGY

Experimental Study and Design Methodology of Sacrificial-Energy Dissipation Beam-Column Joint

Experimental study on PSPC beam – Concrete encased CFST column frame installed with novel steel panel dampers

Experimental and numerical investigation of a novel passive energy dissipation system with viscoelastic damper and angle-reaction controller

Development of double-stage yielding coupling beam damper

Concept and numerical analysis of a double-stage coupling damper for multilevel seismic protection

Analytical development and experimental investigation of the casting multi-plate damper (CMPD)

Seismic behavior and resilience assessment of prefabricated beam–column joint with replaceable graded-yielding energy-dissipating connectors

Experimental investigation and seismic response behavior of a self-centering precast concrete frame with hysteretic dampers

Experimental investigation of prefabricated beam-to-column steel joints for precast concrete structures under cyclic loading

Experimental Study on a Damage-Control and Repairable Fully Precast Beam-Column Joint

The Hysteresis Behavior of Steel Beam–Column Joint with the Load Bearing-Energy Dissipation Connection for Converter Station Building

Seismic behavior evaluation of friction-bearing type connection with slit dampers

Experimental study on seismic performance of prefabricated viscoelastic damping bolted joints

Seismic performance study of a novel steel truss energy dissipation coupling beam

Experimental study on demountable and reusable steel beam-to-column joints with bolted-pinned connections