Abstract:This study explores the influence of chemical composition and cooling rate on the microstructural formation of Al-based alloys, predominantly alloyed with Mn and Ce. Approximately 1 kg of the alloys with varying alloying element content was prepared in a protective resistance furnace. The solidified alloys were then sectioned into 100 g pieces, remelted, and cast into massive copper molds, resulting in samples with different thicknesses ranging from 0.3 to 6 mm. The cooling rates were precisely determined using numerical simulation, ranging from 10 3 to 10 4 K/s. The experimental results demonstrate that, at moderately high cooling rates (above 10 3 K/s), the primary intermetallics precipitated were identified as Al 20 Mn 2 Ce. However, at lower cooling rates, particularly when the Mn and Ce content were high, the formation of the "τ"-phase, Al 8 Mn 4 Ce, was observed and characterized by its detrimental dendrite-like morphology. Interestingly, as the cooling rate approached 10 5 K/s and in the presence of an optimal chemical composition (with sufficiently high Mn and Ce content), an amorphous structure formed at the outer surface of the samples. This amorphous structure exhibits intriguing potential for certain applications due to its unique properties. The desirable microstructure of bulk samples consists of submicron intermetallic compounds embedded in a boundary-free Al-matrix, which is promising for enhancing material strength and performance. This investigation sheds light on the crucial role of chemical composition and cooling rate in controlling the microstructural features of Al-based alloys, thereby providing valuable insights for the development of advanced materials with tailored properties for specific industrial applications. The role of rare earth metals (Ce and La) as poisoning and GFA (glass-forming ability) contributing elements is clarified. The Widmanstätten structure, appeared in the presence of high content of Mn, is discovered.

Micro-structural characteristics and indentation behavior of Ce-Al-Ga alloys

Glassy nature of Ce65Al25Co10 alloy: A metallic glass

Structural origin of the high glass-forming ability of Ce70Ga10Cu20 alloys

A brief review on Ce and Zr-based phase-separated metallic glasses

Microstructural evolution and analysis of Zr–Co/Cu–Al glassy composites and crystallized alloys via indentation and MD simulations

Micro-alloying effects of Co on structural and dynamic properties of CeAlCu glass-forming melts by ab initio molecular dynamics simulations

Long-Range Topological Order In Metallic Glass

Origin of pressure-induced crystallization of Ce75Al25 metallic glass.

Microstructure and crystallization in Cu50Zr45Al5 metallic glass

Low Temperature Transport Properties Of Ce-Al Metallic Glasses

Microstructure of Gravity-Cast and Suction-Cast Aluminium–Cerium-Based Alloys

Microstructure Formation of Al-Based Alloys in the Presence of Rare Earth Metals (Ce, La) and Mn under High Cooling Rate

Systematic discovery of new nano-scale metastable intermetallic eutectic phases in laser rapid solidified Aluminum-Germanium alloy

Low-density to high-density transition in Ce75Al23Si2 metallic glass.

Impact of micro-indentation load/time and Zinc concentration on the thermo- mechanical characteristics of amorphous Se78Te20Sn2 alloy

Unraveling the influence of some foreign elements on microhardness and thermomechanical characteristics of SeTeSn alloy

Beating Homogeneous Nucleation and Tuning Atomic Ordering in Glass-Forming Metals by Nanocalorimetry

Investigation on crystal structure, electrical and magnetic properties of CeAl(Si1-xGex)

The Structural Relaxation Study of Zr–Cu–Ni–Al Metallic Glass During Heating by Small-Angle X-ray Scattering

Direct Observation of Evolution from Amorphous Phase to Strain Glass

Electronic Structure, Long Range Magnetic Order and Elastic Properties of Cerium Based Non-centro Symmetric Intermetallics CeTAl3 (T = Pd, Pt, Cu, Ag and Au)