Abstract:Purpose: To evaluate the color stability of 3D-printed interim restorations with different surface treatments while immersed in various staining solutions or beverages (artificial saliva, tea, coffee, and wine) for 6 months. Material and methods: An acrylic tooth was prepared for an all-ceramic full-coverage restoration. A laboratory scanner was used to digitize the prepared abutment tooth. A virtual all-ceramic full-coverage restoration was designed on the digitized abutment tooth using a laboratory CAD/CAM software. Eighty abutment teeth and interim restorations were 3D-printed with tooth-colored photopolymerizing resin. The restorations were randomly allocated into two different groups: Polish and Optiglaze. For the Polish group, interim restorations were finished and polished with aluminum oxide finishers/polishers. For the Optiglaze group, one layer of nanofilled, light-polymerizing protective coating was then applied. The 80 printed interim crowns were divided into 4 different groups depending on where they would be immersed: Artificial saliva, coffee, wine, and tea. After the sample allocations, there were 8 experimental groups. Each group was allocated with 10 specimens. Color measurements were obtained using a digital spectrophotometer in conjunction with The CIE L*a*b* system before the immersion and 6 months after the immersion. Two-way analysis of variance (ANOVA) was used to test the effects of surface treatment, immersion liquid, and their interaction on ΔE at 6-month post-immersion. Fisher's protected least significant differences (LSD) was used as post hoc test to compare groups differences (α = .05). Results: There were significant effects of surface treatment [F(1,72) = 13.39, p = 0.000], immersion liquid [F(3,72) = 74.18, p = 0.000], and their interaction [F(3,72) = 16.33, p = 0.000] on ΔE at 6-month post-immersion at the α = .05 level. The polish group showed significantly higher ΔE than the Optiglaze group when immersed in coffee (p < 0.001) and wine (p = 0.015). The Optiglaze group showed significantly higher ΔE than the polish group that was immersed in artificial saliva (p < 0.001). The wine group showed higher ΔE than all other immersion liquid groups for both polish and Optiglaze surface treatments (p < 0.001 for all comparisons). ΔL* showed a reduction that was significantly higher than the 2.0 acceptability threshold in the wine-polish (p < 0.001) and wine-Optiglaze (p < 0.001) groups. ΔE showed a color change that was significantly higher than the perceptibility and acceptability thresholds for all the groups under polish surface treatment (p < 0.001). ΔE also showed a color change that was significantly higher than the perceptibility and acceptability thresholds for artificial saliva, tea, and wine under Optiglaze surface treatment (p = 0.004). Conclusions: 3D-printed interim restorations showed significant discoloration after 6-months immersions in the artificial saliva and common beverages (including tea, coffee, and wine). Among all the chromogenic beverages, red wine caused the most significant discoloration on the interim restorations. When 3D-printed interim restorations are needed for extended intraoral service, nano-filled, light polymerizing protective coating can reduce the restoration discoloration caused by chromogenic beverages. The protective effect is most significant against coffee.

Color stability, surface, and physicochemical properties of three-dimensional printed denture base resin reinforced with different nanofillers

Nanoparticle-Modified 3D-Printed Denture Base Resins: Influence of Denture Cleansers on the Color Stability and Surface Roughness In Vitro

Impact of Nanoparticle Addition on the Surface and Color Properties of Three-Dimensional (3D) Printed Polymer-Based Provisional Restorations

Effect of daily immersion of different beverages on the surface roughness and color stability of 3D‐printed denture base resins

Effect of nanomodified 3D printed photopolymerizable resin on flexural strength, color, and antimicrobial efficacy: An in vitro study

3D printed denture base material: The effect of incorporating TiO2 nanoparticles and artificial ageing on the physical and mechanical properties

Flexural strength, fracture toughness, translucency, stain resistance, and water sorption of 3D‐printed, milled, and conventional denture base materials

The influence of the addition of titanium oxide nanotubes on the properties of 3D printed denture base materials

Enhancing 3D-printed denture base resins: A review of material innovations

Polymethylmethacrylate-Based Nanocomposites for Denture Base Fabrication: Impact of Nanoparticle Type and Concentration on the Color Change In Vitro

Antibiofilm Activity of 3D-Printed Nanocomposite Resin: Impact of ZrO2 Nanoparticles

Innovation and Evaluations of 3D Printing Resins Modified with Zirconia Nanoparticles and Silver Nanoparticle-Immobilized Halloysite Nanotubes for Dental Restoration

The Effects of Beverages and Surface Treatments on the Color Stability of 3D-Printed Interim Restorations

In vitro evaluation of the mechanical and optical properties of 3D printed vs CAD/CAM milled denture teeth materials

Effect of denture cleansers on color stability and surface roughness of denture bases fabricated from three different techniques: Conventional heat-polymerizing, CAD/CAM additive, and CAD/CAM subtractive manufacturing

Effects of Artificial Tooth Brushing and Hydrothermal Aging on the Mechanical Properties and Color Stability of Dental 3D Printed and CAD/CAM Materials

Effect of Different Vat Polymerization Techniques on Mechanical and Biological Properties of 3D-Printed Denture Base

A comparison of the mechanical properties of 3D-printed, milled, and conventional denture base resin materials

3D Printing of Resin Material for Denture Artificial Teeth: Chipping and Indirect Tensile Fracture Resistance

3D Printing of CNT- and YSZ-Added Dental Resin-Based Composites by Digital Light Processing and Their Mechanical Properties

Effects of different 3Y‐TZP nanoparticle concentrations on reinforcing mechanical properties of 3D‐printed resin using stereolithography technology