Abstract:High performance thermal energy systems are crucial in fulfilling the growing demand of thermal energy. Consequently, numerous heat transfer enhancements have been proposed. Some of the promising methods are boiling flow heat transfer, helical coiled tube and metal foam insert. Although the performance of each strategy has been extensively studied, based on our literature review, the effectiveness of combining these strategies has not been investigated. This missing information may impede further development of efficient heat transfer systems. This study is therefore performed to investigate subcooled flow boiling heat transfer in helical tube with copper foam insert. A high-resolution three-dimensional pore scale model that considers the shape, porosity and pore density of the metal foam is developed and validated against the published experimental results. Using the model, the effect of inlet temperature, mass flux, wall heat flux, porosity, pore density and half-filled metal foam are studied. The results suggest that operating parameters have mild effects on the heat transfer performance. In contrast, porosity and pore density show significant influence in heat transfer coefficient and pressure drop. It has also been found that total heat transfer surface area and base area are better in characterizing heat transfer in pore-scale level than porosity and pore density at pore-scale level. Moreover, implementing metal foam at outer half of the tube is observed to offer slightly better heat transfer than implementing it at the inner side by around 4.8%. Overall, this study indicates that helical metal foam tubes offer the best performance at mass flux of 200 kg/m 2 ∙s with performance index of 0.72, while straight tubes with 0.90 porosity has the highest performance index of 0.66. Empirical correlations to relate dimensionless parameters to the Nusselt number and friction factor is generated. Finally, the model developed in this study can serve to provide guidelines for the upcoming studies in boiling in metal foam structure and assist in designing metal foam heat exchangers.

Investigation of Performance and Entropy Generation Rate of Direct Contact Membrane Distillation (DCMD) with Metal Foam: A CFD Study

Air-side Performance of Open-Cell Metal Foams for Use in Dehumidifying Heat Exchangers

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Experimental investigation of permeability and Darcy-Forchheimer flow transition in metal foam with high pore density

Spatial variations of DCMD performance for desalination through countercurrent hollow fiber modules

3D-CFD simulation of hollow fiber direct contact membrane distillation module: Effect of module and fibers geometries on hydrodynamics, mass, and heat transfer

Investigation of thermal performance and entropy generation rate of evacuated tube collector solar air heater with inserted baffles and metal foam: A CFD approach

CFD simulation of heat and mass transport for water transfer through hydrophilic membrane in direct-contact membrane distillation process

Numerical thermal analysis of nanofluid flow through the cooling channels of a polymer electrolyte membrane fuel cell filled with metal foam

Unlocking the Thermal Efficiency of Irregular Open-Cell Metal Foams: A Computational Exploration of Flow Dynamics and Heat Transfer Phenomena

Porosity Effect of Polystyrene Membranes on Desalination Performance: A Combined Experimental and Numerical Heat and Mass Transfer Study in Direct Contact Membrane Distillation

Numerical analysis of the heat transfer enhancement by using metal foam

Optimizing thermal performance in tube-in-tube heat exchangers with metal foam inserts: experimental and RSM analysis

Research on the Performance and Computational Fluid Dynamics Numerical Simulation of Plate Air Gap Membrane Distillation Module

Influence of Foam Morphology on Flow and Heat Transport in a Random Packed Bed with Metallic Foam Pellets-An Investigation Using CFD

Numerical simulation of heat transfer performance in an enclosure filled with a metal foam and nano-enhanced phase change material

A computational fluid dynamics study on TPMS-based spacers in direct contact membrane distillation modules

Modelling and Numerical Simulation of Fluid Flow and Heat Transfer through Open Celled Metal Foam

Heat transfer analysis of subcooled flow boiling in copper foam helical coiled heat exchanger – A pore-scale numerical study

On the Efficiency of Air-Cooled Metal Foam Heat Exchangers

Exergetic analysis of direct contact membrane distillation (DCMD) using PVDF hollow fiber membranes for the desalination brine treatment