Abstract:The paper investigated the effect of selected processing conditions during gear grinding on the value and distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment (TCT) conducted by a continuous single-piece flow method.The gears were carburised with LPC at 920C, then quenched in a 4D Quenching chamber at 7 bar and tempered at 190C for 3 hours. In the next step, the working surfaces of the gear teeth were ground by supplying grinding fluid (GF) to the grinding zone using the WET method and the MQL method with a minimum amount. Measurements were made on the distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment and after the grinding process.The results of the study showed the influence of workpiece speed vw and the method of delivery to the grinding zone GF on selected parameters describing the condition of the technological surface layer of the teeth of gears made of 20MnCr5 steel. The grinding process with a white aluminium oxide grinding wheel causes deterioration in the material's residual stress state. For each of the three analysed workpiece speeds vw, smaller changes in microhardness with respect to the microhardness of the material before grinding occur in the surface layer of samples ground with GF fed with the MQL method. Similarly, residual stress values are in the area of favourable compressive stresses.Environmental considerations and the need to comply with increasingly stringent environmental protection and worker safety regulations are pushing researchers and entrepreneurs to completely eliminate or reduce the consumption of grinding fluids in the grinding process. Based on the research and analysis carried out in this study, it was concluded that applying minimum GF by the MQL method could be an alternative to the conventional WET method.In sustainable manufacturing, it is extremely important to produce high-quality items while reducing the cost of manufacturing and taking care of the environment and workers' health. This includes the manufacture of gears, a basic component used in gear transmissions in the automotive industry, for example. The research has established that it is possible to use the MQL method, which reduces the amount of GF used when grinding the working surfaces of gear teeth, as an alternative to the conventional WET method.The conducted research was the first to determine the most favourable conditions, in terms of the obtained residual stresses and microhardness, for grinding the working surface of gear teeth using the MQL method.

Surface strengthening mechanism of the active grinding carburization

Grinding residual stress optimization under the micro-carburizing effect

Study of 40Cr surface modification grinding force and temperature based on microstructure evolution mechanism

Innovative technology investigation into integrate the surface hardening process with the grinding precision finishing for CBN grinding crankshaft

Study and Analysis of Removing the Carbon Deposition on the Inner Surface of a Turbo-Shaft by Chemically Assisted Magnetic Grinding

Surface modification of ultrahigh strength 300M steel under supercritical carbon dioxide (scCO2)-assisted grinding process

Residual stresses in gear form grinding by considering carburizing heat treatment: multi-field coupled numerical simulation and experimental verification

Research on the surface modification and microstructure evolution during gear profile grinding based on cellular automaton

Properties-accuracy synergistic manufacturing of Ti6Al4V surface based on laser carburizing grinding

Simulation and Experiment of Micro-surface in Pre-stressed Hardening Grinding Process

Experimental Study on the Influence of Surface Carbon Content on Crack Initiation for 20Cr2Ni4A Steel

Multi-Objective Optimization of Surface Integrity in the Grind-Hardening Process

Experimental Investigation on Microstructure Alteration and Surface Morphology While Grinding 20cr2ni4a Gears with Different Grinding Allowance Allocation

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

Surface Morphologies and Microstructure of High-Strength Steel AISI 4820 with Different Heat Treatment During Grinding Process

Surface Morphology and Subsurface Microstructure Evolution when Form Grinding 20cr2ni4a Alloys.

Integrated modeling of the gradient structure evolution during surface mechanical grinding treatment: formation mechanism and mechanical properties

Towards Understanding Subsurface Characteristics in Burn Process of Gear Profile Grinding

Gradient microstructure evolution and hardening mechanism of carburized steel under novel heat treatment

Effect of process parameters on hardness and microstructure of 18CrNiMo7-6 carburized steel in high-speed cylindrical grinding

Effect of grinding conditions of gears made of 20MnCr5 steel after single-piece flow heat treatment on the condition of the surface layer of the tooth working surface