Abstract:1 General Introduction A key to the realization of effective microwave tunable devices, among others, is to develop adaptive materials with superior adjustability of electromagnetic parameters. Since there are two fundamental electromagnetic parameters, namely, permittivity and permeability, the tunable property can then be readily approached by manipulating (i) permittivity directly via the electric field, such as in ferroelectrics and conducting polymer [1, 2], or (ii) permeability via magnetic field, such as in ferromagnetic materials [3], or (iii) permittivity (permeability) indirectly by magnetic field (electric field) such as in multiferroics [4]. A unique class of composite materials is considered here to realize such tunable properties: ferromagnetic microwires with excellent soft magnetic properties and giant magnetoimpedance effect [5,6] were introduced into a polymer matrix material so that an indirect control of permittivity can be tuned by the magnetic field. The principle is that the magnetic field can induce significant variation of the impedance via the skin effect at high frequency. The current distribution along the wire then changes accordingly and induces the dipolar polarization [7]. There have been a few relevant studies on this subject in the open literature. Panina et al. [8] and Acher et al. [9] used the microwire arrays to realize the left-hand materials and tunable properties in the presence of magnetic field. Starostenko et al. [10] gave an in-depth discussion of the magnetic bias effect on the permittivity for random wire composites and proved the feasibility of using the wire composites to control attenuation. Di et al. [11], Marin et al. [12] and Zhang et al. [13] have demonstrated the perspective of microwire composites as microwave absorbers. In addition, our previous studies have shown that this kind of composite prove to be multifunctional for a wide range of potential engineering applications such as sensing and structural health monitoring (see e.g. [14-16]). The aim of this paper is to utilize instrumentation [17] dedicated to precise in-situ measurements of electromagnetic parameters to characterize the microwire composites over a broad frequency range and the field effect on the microwave behaviors of the wire composites for potential structural health monitoring (SHM) application.

Tunable piezoresistivity of low percolation threshold micro-nickel wires/PDMS conductive composite regulated by magnetic field

A Soft Piezoresistive Pressure Sensor Based on Porous Conductive CB/PDMS Composite

Ferromagnetic Microwires Enabled Polymer Composites for Sensing Applications

Magnetic-Assisted Transparent and Flexible Percolative Composite for Highly Sensitive Piezoresistive Sensor Via Hot Embossing Technology

Improved conductivity and piezoresistive properties of Ni-CNTs cement-based composites under magnetic field

Novel Magnetic Microwires-Embedded Composites for Structural Health Monitoring Applications

Piezoresistive anisotropy in conductive silicon rubber/multi-walled carbon nanotube/nickel particle composites via alignment of nickel particles

Microwave tunable composites with melt-extracted magnetic microwires

Field/stress Tunable Behaviour of Composites Containing the Combined Current-Modulation Annealed Ferromagnetic Microwires

Contact Piezoresistive Sensors Based on Electro-Polymerized Polypyrrole and a Regulated Conductive Pathway

Ultrasensitive Flexible Pressure Sensors with Broad Linear Detection Range Enabled by Magnetically Induced Self‐Assembled Parallel Circuit

A Flexible and Ultra-Highly Sensitive Tactile Sensor through a Parallel Circuit by a Magnetic Aligned Conductive Composite

Reliable and Scalable Piezoresistive Sensors with an MXene/MoS 2 Hierarchical Nanostructure for Health Signals Monitoring

Low-Cost and Highly Sensitive Pressure Sensor with Mold-Printed Multi-Walled Carbon Nanotubes Dispersed in Polydimethylsiloxane

Advancing pressure sensors performance through a flexible MXene embedded interlocking structure in a microlens array

The tunable sensing behaviors of flexible conductive PDMS/NCG composites via regulation of filler size prepared by a facile sedimentation method

Anisotropic Piezoresistive Sensors Made with Magnetically Induced Vertically Aligned Carbon Nanotubes/Polydimethylsiloxane

3D printed piezoelectric BNNTs nanocomposites with tunable interface and microarchitectures for self-powered conformal sensors

Optimized CNT-PDMS Flexible Composite for Attachable Health-Care Device

Tunable Electrical and Mechanical Responses of PDMS and Polypyrrole Nanowire Composites

Tunable dielectric constants and mechanical properties of PDMS and conducting polymer nanowire composites