Abstract:Schematic of Microwave Assisted Chemical Recycling (MACR) of waste GFRP (Glass Fiber Reinforced Plastic) laminate and fabrication of RGFE laminates. Global glass fiber reinforced plastic (GFRP) recycling provides an effective solution to the end‐of‐life wastes and industrial scrap, by which we can construct a closed‐loop system that reduces environmental impact while increasing sustainability. This study reports the tensile, flexural and shear properties of GFRP composites fabricated from reclaimed fibers from the waste GFRP. A hybrid recycling technique that is, microwave assisted chemical recycling has been used for recovering the glass fiber fabrics. The quantity of solvents (a mixture of 30% H2O2 and CH3COOH in 1:1 ratio) required (in mL/g) for degrading the polymer is optimized with respect to the amount of microwave irradiation time. The microwave irradiation duration was varied at constant power of 900 W for optimizing the quantity of solvent used. SEM analysis of both virgin and reclaimed fiber surfaces indicate an almost complete degradation of polymer from the waste composites. RGFE laminates, fabricated from reclaimed glass fiber fabrics, exhibited marginally higher tensile strength (7%–8%) and significant lower tensile modulus (~29%). On the other hand, RGFE composites demonstrated a greater strain to failure of ~44% compared to VGFE composites during tensile testing, consequently leading to a subsequent increase in tensile toughness by ~28%. The ILSS values obtained from SBS tests and storage modulus and loss factor curves from DMA tests showed almost similar values. SEM studies revealed the probable causes of failures of the samples for tensile and flexural tests. Highlights Hybrid recycling technique using microwave irradiation is optimized. Amount of solvent used is optimized by varying the irradiation times. Tensile and flexural strengths exhibit a marginal increase of 7%–8%. Significant rise in strain at failure by 44% and tensile toughness by 28%. Fractography studies have been performed for analyzing failures.

Recycling of Thermoplastic Glass Fiber‐Reinforced Composites Using High‐Voltage Fragmentation

High-quality Electrostatic Recycling of Waste Carbon Fiber Via Spark-Driven Shock Waves and Joule Heating

Dissolution recycling for recovery of polypropylene and glass fibres

The Recycling of Comminuted Glass-Fiber-Reinforced Resin from Electronic Waste

Thermal Regeneration and Reuse of Carbon and Glass Fibers from Waste Composites

Recycling of fiber reinforced composites: Online mass spectrometric tracing, offline physicochemical speciation and toxicological evaluation of a pilot plant pyrolytic conversion

Recyclability of take‐back glass fiber‐reinforced blends of polyphenylene oxide with high‐impact polystyrene for high‐performance engineering applications

Comparing tensile, bending and interlaminar shear performance of GFRP composites fabricated using recovered and virgin glass fibers: Optimization of the microwave assisted chemical recycling technique

A Study to Investigate the Mechanical Properties of Recycled Carbon Fibre/Glass Fibre-Reinforced Epoxy Composites Using a Novel Thermal Recycling Process

Microwave pyrolysis as a method of recycling glass fibre from used blades of wind turbines

Thermally recyclable and reprocessable glass fiber reinforced high performance thermosetting polyurethane vitrimer composites

Thermal–Mechanical Delamination for Recovery of Tempered Glass from Photovoltaic Panels

Recycling of an acrylate–glass fiber reinforced polyester composite

Experimental and multi-scale investigation of the mechanical behavior of mechanically recycled glass fiber reinforced thermoplastic composites

Technologies for Mechanical Recycling of Carbon Fiber-Reinforced Polymers (CFRP) Composites: End Mill, High-Energy Ball Milling, and Ultrasonication

Recyclability of unidirectional reinforced pultruded thermoplastic profiles into composite laminates

Study on Recycling of Waste Glass Fiber Reinforced Polypropylene Composites: Examination of Mechanical and Thermal Properties

Mechanical recycling process: An alternative for a viable disposal of carbon fiber‐reinforced thermoplastic waste

Thermal Recycling Process of Carbon Fibers from Composite Scrap—Characterization of Pyrolysis Conditions and Determination of the Quality of Recovered Fibers

Recycling Glass Fiber from Polyurethane Composite by Pyrolysis Strategy with High Mechanical Properties

Efficient method of recycling carbon fiber from the waste of carbon fiber reinforced polymer composites