Abstract:During the past years, the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has increased from 3.8% to 25.7%, making them the best candidate for the next-generation photovoltaic devices. Two dominant PSC architectures have evolved, a regular n-i-p structure with mesoscopic or planar heterojunction and an inverted p-i-n planar structure. Compared to the regular n-i-p PSCs, the inverted p-i-n PSCs possess the advantages of lower synthesis temperature, no hysteretic effect and good compatibility with the tandem solar cells. For p-i-n PSCs, the hole transport layer (HTL) determines the hole transport efficiency and crystallinity of perovskite, so it plays a crucial role in the stacked devices. The conventional organic HTL of PEDOT:PSS-based PSCs can achieve satisfying PCEs, but may be able to impede the commercialization of perovskite photovoltaic devices because of their high price and acidity-induced poor stability. By comparison, the inorganic P-type NiOx with wide band gap exhibits low cost, superior chemical stability and high hole mobility without corrosion to perovskite layer. Unlike the most reported spin-coated NiOx nanoparticle films, we used sputtered NiOx as HTL for application in FA-based PSCs and achieved a PCE of 20.05%. After systematically optimizing the sputtering parameters, including power, time and argon flow rate, we obtained better crystal quality, better transparency, proper energy level, and higher hole mobility of NiOx film. Reducing the interstitial vacancies and defects in NiOx films attributes to decreased nonradiative recombination losses, which mainly cause the hole accumulation near the perovskite/NiOx interface. Finally, a champion device with open-circuit voltage (Voc) of 1.09 V, current density (Jsc) of 23.4 mA/cm 2 , fill factor (FF) of 78% and PCE of 20.05% are obtained. This work has important significance for preparation of large-area perovskite solar cell modules.

Vapor Deposition of FAI on SnO 2 Provides Interface Modification and Crystallization Control for High-Performance and Stable Perovskite Solar Cells

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Modification of SnO2 by Acidic FAAc-HI Solution for Efficient and Stable Perovskite Solar Cells with a Multifunctional Interface

Facilitating the formation of SnO2 film via HfO2-modified FTO electrode for efficient perovskite solar cells

Novel Bilayer SnO2 Electron Transport Layers with Atomic Layer Deposition for High-Performance α-FAPbI3 Perovskite Solar Cells.

Regulating the Crystallization of FAPbI3‐Based Perovskite with a Furan Substituted Ethylammonium Additive for Achieving Highly Efficient Solar Cells

Enhanced photovoltaic performance of SnO2 based flexible perovskite solar cells via introducing interfacial dipolar layer and defect passivation

Facile modification on buried interface for Highly Efficient and Stable FASn0.5Pb0.5I3 Perovskite Solar Cells with NiOx Hole‐Transport layers

Suppressed Ion Migration in FA‐Rich Perovskite Photovoltaics through Enhanced Nucleation of Encapsulation Interface

SnO2 Surface Modification and Perovskite Buried Interface Passivation by 2,5‐Furandicarboxylic Acid for Flexible Perovskite Solar Cells

Highly Efficient and Stable FASnI3 Perovskite Solar Cell via Modification with Tetrapotassium Hexacyanoferrate

Passivating Defects via Retarding the Reaction Rate of FAI and PbI2 Enables Stable Perovskite Solar Cells

Multifunctional Molecule‐Modified SnO 2 –Perovskite Interface for Efficient Planar Perovskite Solar Cells

F-doping-Enhanced Carrier Transport in the SnO<sub>2</sub>/Perovskite Interface for High-Performance Perovskite Solar Cells

ZnO/SnO2 bilayer electron transport layer strategy to improve the performance of FAPbI3 solar cell

Highly efficient and stable FASnI3 perovskite solar cells with effective interface modulation by PEABr treated low-dimensional perovskite layer.

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

Modulation of Nucleation and Crystallization in PbI2 Films Promoting Preferential Perovskite Orientation Growth for Efficient Solar Cells

Amorphous F‐doped TiOx Caulked SnO2 Electron Transport Layer for Flexible Perovskite Solar Cells with Efficiency Exceeding 22.5%

Reduced Defects of MAPbI3 Thin Films Treated by FAI for High‐Performance Planar Perovskite Solar Cells

Sputtered Niox Films As Hole Transport Layers for FA-Based Perovskite Solar Cell Application