Abstract:In the present work, the effects of Bi-Mg co-doping on the thermoelectric properties of SnTe materials are investigated. Pristine SnTe and Sn 0.96 Bi 0.02 Mg 0.02 Te materials are synthesized using a facile solvothermal technique. Calculated crystallite size and grain size decrease after Bi-Mg co-doping. In Sn 0.96 Bi 0.02 Mg 0.02 Te various lattice defects, lattice strain, stacking fault and dislocation densities are higher as compared to pristine SnTe. Minimum lattice thermal conductivity is 0.21 W/mK in Sn 0.96 Bi 0.02 Mg 0.02 Te and 1.13 W/mK in pristine SnTe at 584 K. Lower lattice thermal conductivity in Bi-Mg co-doped SnTe may be due to more phonon scattering at interfaces and lattice defects. A decrease in carrier concentration following doping may lead to a decrease in electrical conductivity in Sn 0.96 Bi 0.02 Mg 0.02 Te as compared to SnTe. Maximum S in Sn 0.96 Bi 0.02 Mg 0.02 Te is 72 μV/K and in pure SnTe is 66 μV/K at 584 K. The increase in S may be due to band engineering via Bi-Mg co-doping as (i) Bi generates resonant energy states at the Fermi level of SnTe (ii) Mg doping modifies the band structure of SnTe via converging valence bands and widening the band gap. Maximum 'figure of merit' zT = 0.21 in Sn 0.96 Bi 0.02 Mg 0.02 Te is 91% higher than pristine SnTe at 584 K. Material quality factor ( B = B E T / κ L ) indicates that maximum zT > 1 can be achieved until S = 246 μV/K in Sn 0.96 Bi 0.02 Mg 0.02 Te. The electronic contribution of quality factor falls after doping which demonstrates that the increase in zT is caused by a decrease in lattice thermal conductivity. The thermoelectric efficiency and figure of merit ' ZT' of thermoelectric devices composed of Sn 0.96 Bi 0.02 Mg 0.02 Te are almost double those of pristine SnTe. Thus experimental findings reveal that Bi-Mg co-doped SnTe can be a potential thermoelectric material.

First-principles Calculations to Investigate Probing the Influence of Mn and Mg Doping Concentration on Electronic Structures and Transport Properties of SnTe Alloys

Manipulation of Band Structure and Interstitial Defects for Improving Thermoelectric SnTe

Approaching the Minimum Lattice Thermal Conductivity of P-Type SnTe Thermoelectric Materials by Sb and Mg Alloying.

Interplay between metavalent bonds and dopant orbitals enables the design of SnTe thermoelectrics

Balancing electron and phonon scatterings while tailoring carrier concentration in SnTe for enhancing thermoelectric performance

Valence band engineering and thermoelectric performance optimization in SnTe by Mn-alloying via a zone-melting method

Structural Evolution of High‐Performance Mn‐Alloyed Thermoelectric Materials: A Case Study of SnTe

Mechanical alloying boosted SnTe thermoelectrics

Optimization of Mechanical and Thermoelectric Properties of SnTe-Based Semiconductors by Mn Alloying Modulated Precipitation Evolution

Improved Solubility in Metavalently Bonded Solid Leads to Band Alignment, Ultralow Thermal Conductivity, and High Thermoelectric Performance in SnTe

Fine electron and phonon transports manipulation by Mn compensation for high thermoelectric performance of Sb2Te3(SnTe)n materials

Multiscale Defects as Strong Phonon Scatters to Enhance Thermoelectric Performance in Mg2Sn1-xSbx Solid Solutions

Enhancing the Thermoelectric Performance of Mg2Sn Single Crystals Via Point Defect Engineering and Sb Doping.

Achieving Ultralow Lattice Thermal Conductivity and High Thermoelectric Performance in SnTe by Alloying with MnSb 2 Se 4

Improvement in thermoelectric properties of Bi-Mg co-doped SnTe via band engineering and nanostructuring

Advancing thermoelectrics by vacancy engineering and band manipulation in Sb-doped SnTe–CdTe alloys

Effect of Mg Substitution on Structural, Electronic, Optical and Thermoelectric Properties of ZnTe Alloy

Raised solubility in SnTe by GeMnTe2 alloying enables converged valence bands, low thermal conductivity, and high thermoelectric performance

Interstitial Defects Facilitate Dense Dislocations and Band Convergence for High Thermoelectric Performance in SnTe

Constructing Coated Grain Nanocomposites and Intracrystalline Precipitates to Simultaneously Improve the Thermoelectric and Mechanical Properties of SnTe by MgB2 and Sb Co‐Doping

Enhanced Average Thermoelectric Figure of Merit of the PbTe-SrTe-MnTe Alloy.