Abstract:Objective: This study used finite element analysis to simulate four commonly used fixation methods for metacarpal shaft oblique fractures during finger motion and evaluate their biomechanical performance. The aim was to provide evidence for clinically selecting the optimal fixation method, guiding early rehabilitation treatment, and reducing the risk of complications. Methods: Finite element analysis simulated dynamic proximal phalanx motion (60° flexion, 20° extension, 20° adduction, and 20° abduction). We analysed stress, displacement, and distributions for dorsal plates, intramedullary nails, Kirschner wire, and screw fixation methods. Results: At 60° of finger flexion and 20° of abduction, plate fixation demonstrated greater stability and minimal displacement, with a peak displacement of 0.19 mm; however, it showed higher stress levels in all motion states, increasing the risk of failure. The stability of the intramedullary nail was similar to that of the dorsal plate, with a maximum displacement difference of 0.04 mm, and it performed better than the dorsal plate during adduction of 20°. Kirschner wire showed the highest stress levels of 81.6 Mpa during finger flexion of 60°, indicating a greater risk of failure and unstable displacement. Screws had lower stress levels in all finger motion states, reducing the risk of failure, but had poorer stability. Stress and displacement distributions showed that the dorsal plate, intramedullary nail, and Kirschner wire mainly bore stress on the implants, concentrating near the fracture line and the proximal metacarpal. In contrast, the screws partially bore stress in the screw group. The anterior end of the metacarpal mainly hosted the maximum displacement. Conclusion: This study demonstrates that under simulated finger motion states, the dorsal plate fixation method provides the best stability in most cases, especially during finger flexion and abduction. However, high stress levels also indicate a higher risk of failure. The intramedullary nail is similar to the dorsal plate in stability and performs better in certain motion states. Kirschner wire exhibits the highest risk of failure during flexion. Although screws have poorer stability in some motion states, they offer a lower risk of failure. These findings provide important reference and surgical selection strategies for treating metacarpal fractures.

Biomechanical analysis of plate versus K-wire fixation for metacarpal shaft fractures with wedge-shaped bone defects

Effect of a figure-of-eight cerclage wire with two Kirschner wires on fixation strength for transverse metacarpal shaft fractures: an in vitro study with artificial bone

The biomechanical evaluation of metacarpal fractures fixation methods during finger movements: a finite element study

[Biomechanical Research of Antegrade Intramedullary Fixation for the Metacarpal Fractures].

Locking Plate Alone versus in Combination with Two Crossed Kirschner Wires for Fifth Metacarpal Neck Fracture

Comparative analysis of the effects of AO mini-plate and Kirschner wire pinning in the metacarpal fractures: A retrospective study

Plate Versus Kirschner Wire Fixation in Treatment of Fourth and Fifth Carpometacarpal Fracture-Dislocations: A Retrospective Cohort Study

Biomechanical Comparison of Fixation of Metacarpal Shaft Fractures With Intramedullary Threaded Nail and Dorsal Plate

Cadaveric biomechanical assessment of different configurations for a novel pin and plate fixation method in distal humerus fractures

Percutaneous Reduction and Fixation Technique for 4th Metacarpal Shaft Fracture

Biomechanical analysis of posteromedial tibial plateau split fracture fixation.

Osteosynthesis of Phalangeal Fractures: Biomechanical Comparison of Kirschner Wires, Plates, and Compression Screws

Intramedullary Nailing Versus Plating for Extra-Articular Distal Tibial Metaphyseal Fracture: A Systematic Review and Meta-Analysis

Using Suture and Locking Anatomical Bridging Plate to Fix Comminuted Mid-Shaft Clavicle Fractures with Intramedullary Nail Assistance in Reduction.

A Biomechanical Study of an Alternative Internal Fixation Method for Transverse Patella Fractures

Biomechanical analysis of four different fixations for the posterolateral shearing tibial plateau fracture.

Comprehensive biomechanical analysis of three clinically used fixation constructs for posterior malleolar fractures using cadaveric and finite element analysis

Retraction Note: Mini-plate Versus Kirschner Wire Internal Fixation for Treatment of Metacarpal and Phalangeal Fractures in Chinese Han Population: a Meta-Analysis

Alternative Surgical Treatment Method for 5th Metacarpal Neck Fractures: Comparison of Clinical Outcomes of Intramedullary and Transverse K-Wire Fixations with Additional Antirotational K-Wire

Computational analysis of the biomechanical stability of internal fixation of the lateral tibial plateau fracture: A mechanical stability study

Efficacy comparison between intramedullary nail fixation and plate fixation in distal tibia fractures: a meta-analysis of randomized controlled trials