Abstract:CONSPECTUS: To tackle the foreseen energy crisis and serious environmental problem caused by conventional energy resources, solar cells, or photovoltaics (PV), a technology that can directly convert sunlight to electricity has been considered to be one of the most important and cost-effective clean energy techniques that benefit the environment. So far, silicon-based PVs have dominated the market due to mature fabrication techniques and their relatively good power conversion efficiency (PCE) and excellent stability. In the past decades, metal halide perovskite PVs have been a major direction of current PV research owing to their intriguing optoelectronic performance. The record PCE of perovskite PV cells has unprecedently increased from an original 3.8 to 25.5%. The typical structure of a photovoltaic perovskite is ABX(3), where A refers to a monovalent cation such as methylammonium (MA(+)), cesium (Cs+), or formamidinium (FA(+)); B refers to a divalent cation such as Pb2+ or Sn2+; and X refers to a halide anion. In general, a perovskite PV device consists of an active layer of the perovskite absorber, which is connected by a hole-transporting layer (HTL) and an electron-transporting layer (ETL). In the beginning, the strategies to improve the PCEs mainly focused on developing an effective method to grow a smooth and continuous polycrystalline film. After the improvement of the baseline PCE of the perovskite PVs, various techniques were employed to reduce the defects of perovskite formed at grain boundaries and surfaces, further pushing the PCEs of perovskite PV devices to over 20%. In the meantime, the discovery of suitable and low-cost interfacial materials such as electron-transporting materials and hole-transporting materials has appealed to the attention of the perovskite research community to accelerate the commercialization of the perovskite PVs. In this Account, we start from our efforts to develop facile and effective fabrication strategies to obtain smooth and continuous polycrystalline perovskite thin films, including vapor-assisted and moisture-assisted perovskite crystal growth. The strategies and the in-depth mechanisms of preventing the formation of specific detrimental defects accumulated at grain boundaries or the surface are also portrayed by designing various passivation molecules with certain functional groups, such as carbonyl groups, amine groups, or sulfonic groups. Some systematically designed electron- or hole-transporting materials to improve the charge extraction and collection efficiency in perovskite PV devices are discussed as well. Finally, future perspectives for further enhancing the long-term stability and PCE are proposed to accelerate the commercialization of perovskite PV devices in the next decade.

Intermediate phase engineering towards efficient and stable perovskite solar cells: Principles and strategies

Inorganic perovskite solar cells: an emerging member of the photovoltaic community

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Recent advances in the interfacial engineering of organic–inorganic hybrid perovskite solar cells: a materials perspective

Recent Progress of Critical Interface Engineering for Highly Efficient and Stable Perovskite Solar Cells

Ionic Liquids Engineering for High-Efficiency and Stable Perovskite Solar Cells

Interface Engineering for Highly Efficient and Stable Perovskite Solar Cells

Towards highly stable and efficient planar perovskite solar cells: Materials development, defect control and interfacial engineering

Recent advances in interface engineering of all-inorganic perovskite solar cells.

Review on Practical Interface Engineering of Perovskite Solar Cells: From Efficiency to Stability

Intermediate Phase Enhances Inorganic Perovskite and Metal Oxide Interface for Efficient Photovoltaics

Recent Advances in CsPbX3 Perovskite Solar Cells: Focus on Crystallization Characteristics and Controlling Strategies

Material and Interface Engineering for High-Performance Perovskite Solar Cells: A Personal Journey and Perspective

Recent advances on interface engineering of perovskite solar cells

Strategies for the preparation of high-performance inorganic mixed-halide perovskite solar cells

Intermediate Phase Modification Enables High‐Performance Iodine‐Rich Inorganic Perovskite Solar Cells with 3000‐Hour Stability

Intermediates transformation for efficient perovskite solar cells

Intermediate-Controlled Interfacial Engineering for Stable and Highly Efficient Carbon-Based PSCs

Interfaces and Interfacial Layers in Inorganic Perovskite Solar Cells

Recent Progress of Carbon‐Based Inorganic Perovskite Solar Cells: From Efficiency to Stability