Abstract:CONSPECTUS: To tackle the foreseen energy crisis and serious environmental problem caused by conventional energy resources, solar cells, or photovoltaics (PV), a technology that can directly convert sunlight to electricity has been considered to be one of the most important and cost-effective clean energy techniques that benefit the environment. So far, silicon-based PVs have dominated the market due to mature fabrication techniques and their relatively good power conversion efficiency (PCE) and excellent stability. In the past decades, metal halide perovskite PVs have been a major direction of current PV research owing to their intriguing optoelectronic performance. The record PCE of perovskite PV cells has unprecedently increased from an original 3.8 to 25.5%. The typical structure of a photovoltaic perovskite is ABX(3), where A refers to a monovalent cation such as methylammonium (MA(+)), cesium (Cs+), or formamidinium (FA(+)); B refers to a divalent cation such as Pb2+ or Sn2+; and X refers to a halide anion. In general, a perovskite PV device consists of an active layer of the perovskite absorber, which is connected by a hole-transporting layer (HTL) and an electron-transporting layer (ETL). In the beginning, the strategies to improve the PCEs mainly focused on developing an effective method to grow a smooth and continuous polycrystalline film. After the improvement of the baseline PCE of the perovskite PVs, various techniques were employed to reduce the defects of perovskite formed at grain boundaries and surfaces, further pushing the PCEs of perovskite PV devices to over 20%. In the meantime, the discovery of suitable and low-cost interfacial materials such as electron-transporting materials and hole-transporting materials has appealed to the attention of the perovskite research community to accelerate the commercialization of the perovskite PVs. In this Account, we start from our efforts to develop facile and effective fabrication strategies to obtain smooth and continuous polycrystalline perovskite thin films, including vapor-assisted and moisture-assisted perovskite crystal growth. The strategies and the in-depth mechanisms of preventing the formation of specific detrimental defects accumulated at grain boundaries or the surface are also portrayed by designing various passivation molecules with certain functional groups, such as carbonyl groups, amine groups, or sulfonic groups. Some systematically designed electron- or hole-transporting materials to improve the charge extraction and collection efficiency in perovskite PV devices are discussed as well. Finally, future perspectives for further enhancing the long-term stability and PCE are proposed to accelerate the commercialization of perovskite PV devices in the next decade.

Intermediates transformation for efficient perovskite solar cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Intermediate phase engineering towards efficient and stable perovskite solar cells: Principles and strategies

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Morphology Evolution of High Efficiency Perovskite Solar Cells via Vapor Induced Intermediate Phases

2,2‐Azodi(2‐Methylbutyronitrile)‐coordinated Intermediate Phase Engineering for Efficient and Stable Perovskite Solar Cells

Management of Perovskite Intermediates for Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

Hydrogen-bond-bridged intermediate for perovskite solar cells with enhanced efficiency and stability

Interface Engineering for Highly Efficient and Stable Perovskite Solar Cells

Engineering the intermedi-ate adduct phase to con-trol the crys-tallization of perovskites for efficient and stable perov-skite solar cells

Manipulated Crystallization and Passivated Defects for Efficient Perovskite Solar Cells via Addition of Ammonium Iodide

Interfaces and Interfacial Layers in Inorganic Perovskite Solar Cells

Intermediate Phase Modification Enables High‐Performance Iodine‐Rich Inorganic Perovskite Solar Cells with 3000‐Hour Stability

Post-treatment techniques for high-performance perovskite solar cells

Morphology Optimization of Perovskite Films for Efficient Cells and Modules through Solvent Engineering

Perylene Monoimide Phosphorus Salt Interfacial Modified Crystallization for Highly Efficient and Stable Perovskite Solar Cells

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

Aquointermediate Assisted Highly Orientated Perovskite Thin Films Toward Thermally Stable and Efficient Solar Cells

Optimization of Α-Fapbi3 Crystallization by Intermediate Compounds Transformation for Efficient and Stable Perovskite Solar Cells

Improving the Efficiency of Perovskite Solar Cells Through Optimization of the CH 3 NH 3 PbI 3 Film Growth in Solution Process Method