Abstract:Abstract. Wind data collection in the atmospheric boundary layer benefits from short-term wind speed measurements using unmanned aerial vehicles. Fixed-wing and rotary-wing devices with diverse anemometer technology have been used in the past to provide such data, but the accuracy still has the potential to be increased. A lightweight drone for carrying an industry-standard precision sonic anemometer was developed. Accuracy tests have been performed with the isolated anemometer at high tilt angles in a calibration wind tunnel, with the drone flying in a large wind tunnel and with the full system flying at different heights next to a bistatic lidar reference. The propeller-induced flow deflects the air to some extent, but this effect is compensated effectively. The data fusion shows a substantial reduction of crosstalk (factor of 13) between ground speed and wind speed. When compared with the bistatic lidar in very turbulent conditions, with a 10 s averaging interval and with the unmanned aerial vehicle (UAV) constantly circling around the measurement volume of the lidar reference, wind speed measurements have a bias between −2.0 % and 4.2 % (root-mean-square error (RMSE) of 4.3 % to 15.5 %), vertical wind speed bias is between −0.05 and 0.07 m s−1 (RMSE of 0.15 to 0.4 m s−1), elevation bias is between −1 and 0.7∘ (RMSE of 1.2 to 6.3∘), and azimuth bias is between −2.6 and 7.2∘ (RMSE of 2.6 to 8.0∘). Key requirements for good accuracy under challenging and dynamic conditions are the use of a full-size sonic anemometer, a large distance between anemometer and propellers, and a suitable algorithm for reducing the effect of propeller-induced flow. The system was finally flown in the wake of a wind turbine, successfully measuring the spatial velocity deficit and downwash distribution during forward flight, yielding results that are in very close agreement to lidar measurements and the theoretical distribution. We believe that the results presented in this paper can provide important information for designing flying systems for precise air speed measurements either for short duration at multiple locations (battery powered) or for long duration at a single location (power supplied via cable). UAVs that are able to accurately measure three-dimensional wind might be used as a cost-effective and flexible addition to measurement masts and lidar scans.

Next generation combined sonic-hotfilm anemometer: wind alignment and automated calibration procedure using deep learning

Combined hot-film anemometers for measuring flow speed vectors

Calibration of 3-D wind measurements on a single-engine research aircraft

A two-dimensional flow sensor with integrated micro thermal sensing elements and a back propagation neural network

Improving Large Angle Flow Measurement Accuracy of Five-Hole Probe Using Novel Calibration Coefficient and Accuracy Progressive Neural Network

Aerosense: Long-Range Bluetooth Wireless Sensor Node for Aerodynamic Monitoring on Wind Turbine Blades

A micro-hot-wire anemometry probe with elongated stubs for turbulent boundary layer measurements

Fast-response hot-wire flow sensors for wind and gust estimation on UAVs

A Nonlinear Observability Analysis of Ambient Wind Estimation with Uncalibrated Sensors, Inspired by Insect Neural Encoding

A novel laser Doppler anemometer (LDA) for high-accuracy turbulence measurements

Visual anemometry: physics-informed inference of wind for renewable energy, urban sustainability, and environmental science

Towards accurate and practical drone-based wind measurements with an ultrasonic anemometer

Improving the measurement of air-water flow properties using remote distance sensing technology

Developing the next generation of dual-tip phase-detection probes for air-water flow experiments

A Framework of Data Assimilation for Wind Flow Fields by Physics-informed Neural Networks

Ensemble-based, large-eddy reconstruction of wind turbine inflow in a near-stationary atmospheric boundary layer through generative artificial intelligence

Theoretical Calibration and Experimental Test of Hemispherical Seven-Hole Probe Under 3-D Flow Field in Wind Tunnel

Large-Scale Flow Measurements and Analysis for Radial Inlets of Industrial Centrifugal Compressors Based on Multi-hole Probe System

A bio-inspired real-time capable artificial lateral line system for freestream flow measurements

Wind Profile Reconstruction Based on Convolutional Neural Network for Incoherent Doppler Wind LiDAR