Abstract:Hierarchical ZSM‐5 zeolite materials with different SiO2/Al2O3 molar ratios in the range of 60–300 were synthesized using soft templating and microemulsion methods to generate zeolite materials with narrow mesopore size distributions. The resulting materials were characterized by X‐ray flourescence (XRF), Fourier transform infra‐red (FTIR) spectroscopy, X‐ray diffraction (XRD), scanning electron microscopy (SEM), ammonia temperature programmed desorption (NH3‐TPD), thermo‐gravimetric analysis (TGA), Brunauer‐Emmett‐Teller (BET) surface area measurements, and products from the catalytic tests were analyzed by gas chromatography (GC). The XRF analysis determined that the Si/Al ratios for the synthesized ZSM‐5 were close to the batch ratios. The XRD and FTIR results revealed that the synthesized samples had crystalline ZSM‐5 zeolite structures. The small angle observed from the XRD patterns confirmed the presence of mesopores in the structure of the prepared materials. The SEM results showed that the ZSM‐5 synthesized materials had different morphologies and particle sizes, as well as worm‐like holes indicating that some macropores with average pore sizes ranging between 68 and 85 nm were successfully generated in these materials. NH3‐TPD results showed that the total acidity of the prepared materials decreased with an increase in the Si/Al (SA) ratio following this trend: SA = 71 > 177 > 345. This may be due to the decrease in the aluminum content, which is largely responsible for the formation of acidic sites in zeolites. The acid strength was found to increase with a decrease in the Si/Al ratio, highlighted by the peak shifts to higher temperatures. From the BET results, the SA = 71 was observed to have the highest SSA of 618 m2/g given by its micropore area of 103 m2/g and an external surface area of 515 m2/g. The high external surface area present in the material was due to the development of mesopores with narrow pore size distribution of approximately 6 nm indicating the success of the microemulsion method for the generation of hierarchical zeolites with well controlled pore sizes. The hierarchical ZSM‐5 catalysts were tested for the cracking of various hydrocarbon chain lengths. Low conversions, less than 10%, were obtained in the cracking of hexane; however, when cracking longer chain C12 hydrocarbons, the conversion increased remarkably to 100%. The catalyst with SA = 71 had the highest selectivity towards ethylene and propylene olefins due to its higher acidity in comparison with the other prepared catalysts. Improved activity, selectivity towards ethylene and propylene greater than 60%, and enhanced catalyst stability were demonstrated when using a hierarchical ZSM‐5 compared to the commercial catalyst in the cracking of dodecane. High selectivity towards light olefins was obtained for the cracking of waste tire‐derived oil. The results suggest that these hierarchical materials are suited to the cracking of long chain hydrocarbons and are promising materials for the valorization of waste tire‐derived oils.

Catalytic co-cracking of biomass and waste plastics with sawdust mediated ZSM-5 synthesized via activating gel process

Synthesis and Physicochemical Characterization of Hierarchical ZSM-5: Effect of Organosilanes on the Catalyst Properties and Performance in the Catalytic Fast Pyrolysis of Biomass

Catalytic Fast Pyrolysis of Cellulose in a Microreactor System Using Hierarchical Zsm-5 Zeolites Treated with Various Alkalis

Controlled Synthesis of Hierarchical ZSM-5 for Catalytic Fast Pyrolysis of Cellulose to Aromatics

Green synthesis of ZSM-5 using silica fume and catalytic co-cracking of lignin and plastics for production of monocyclic aromatics

ZSM–5@KIT–6 encapsulated composite molecular sieves for the catalytic cracking of waste cooking oil model compound to produce light olefins

Self-assembly kieselguhr-based ZSM-5 for catalytic pyrolysis of mask waste to produce high value-added aromatics

[Influence of ZSM-5(38)/Al-MCM-41 Composite Molecular Sieve Catalysts on Pyrolysis of Cellulose].

Tailoring ZSM-5 Zeolites for the Fast Pyrolysis of Biomass to Aromatic Hydrocarbons.

Preparation of sodium silicate/red mud-based ZSM-5 with glucose as a second template for catalytic cracking of waste plastics into useful chemicals

Chitosan-assisted reassembled hierarchical HZSM-5 for selective production of monocyclic aromatics in catalytic co-pyrolysis of biomass and plastic

Production of Renewable Petrochemicals from Catalytic Co-Pyrolysis of Beech Wood and Low-Density Polyethylene with Mesoporous Bifunctional ZSM-5 Zeolites

Tuning the morphology and textural properties of ZSM-5 additive for co-cracking of waste plastics with vacuum gas oil to light olefins

Synthesis of Nanocrystalline Cellulose Induced Hierarchical Porous Zsm-5 for Catalytic Conversion of Low-Density Polyethylene

Effective hierarchical ZSM‐5 catalysts for the cracking of naphtha and waste tire‐derived oil to light olefins

In-depth understanding of the synergistic effect in catalytic copyrolysis of lignin-plastic mixtures with lignin-tailored hierarchical HZSM‐5 catalysts

Thermally stable phosphorus and nickel modified ZSM-5 zeolites for catalytic co-pyrolysis of biomass and plastics

The Effect of Ni-ZSM-5 Catalysts on Catalytic Pyrolysis and Hydro-Pyrolysis of Biomass

Preparation of Mesoporous ZSM-5 Catalysts Using Green Templates and Their Performance in Biomass Catalytic Pyrolysis.

Catalytic co-pyrolysis of poplar tree and polystyrene with HZSM-5 and Fe/HZSM-5 for production of light aromatic hydrocarbons

Improving catalytic production of aromatic hydrocarbons with a mesoporous ZSM-5 modified with nanocellulose as a green template