Abstract:Abstract At present, there are many studies on the residual stress field and plastic strain field introduced by surface strengthening, which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks. However, there are few studies on the effects of these key factors on fretting wear. In the paper, shot-peening (SP) and ultrasonic surface rolling process (USRP) were performed on Ti-6Al-4V plate specimens. The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer. Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester. The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments. The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation, and the mechanism of improving fretting fatigue life by surface strengthening process was further explained. After USRP treatment, the surface roughness of Ti-6Al-4V is significantly improved. In addition, the microhardness of the specimen after SP reaches the maximum at 80 μm from the surface, which is about 123% higher than that of the AsR specimen. After USRP, it reaches the maximum at 150 μm from the surface, which is about 128% higher than that of AsR specimen. It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction, and the residual stress reaches the maximum on the sub surface. The USRP specimen reaches the maximum value at 0.18 mm, about − 550 MPa, while the SP specimen reaches the maximum value at 0.1 mm, about − 380 MPa. The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP. The surface integrity of specimens after USRP is the best, which has deeper residual compressive stress layer and more refined grain. In this paper, a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.

Effect of Coupling Ultrasonic Fatigue Strengthening and Polishing Methods on Open Hole Structures

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Fatigue performance on 7050 aluminum alloy by using ultrasonic vibration-assisted hole expansion strengthening

Study on the composite strengthening with laser shock processing and ultrasonic extrusion strengthening for small hole components

Effect of ultrasonic shot peening on surface integrity and fatigue performance of single-crystal superalloy

Effects of Ultrasonic Shot Peening on Fatigue Behavior of TA15 Titanium Alloy Fabricated by Laser Melting Deposition

Improving fatigue initiation life of open-hole fibre metal laminates by laser shock peening

Investigation on fatigue failure of split-sleeve cold expansion holes of 7075-T651 aluminum alloy

Effect of surface high-density twinned structure on the fatigue crack initiation of Ti-6Al-4V

Study on surface properties and fatigue performance of aluminum alloy plate with prestressed ultrasonic peening

Study of Vibration‐Ultrasonic Combined Fatigue on 7075‐T6 Aluminum Alloy

Influence of Ultrasonic Surface Rolling Process and Shot Peening on Fretting Fatigue Performance of Ti-6Al-4V

Effect of ultrasonic surface deep rolling combined with oxygen boost diffusion treatment on fatigue properties of pure titanium

Experimental study on surface integrity and fatigue life of an ultra-high strength steel by the composite strengthening process of pre-torsion and ultrasonic rolling

Comparison of strengthening effect and fatigue properties of SAF2205 cruciform welded joints by ultrasonic impact and cavitation jet peening treatment

Microstructure and Fatigue Performance of Hard Al Alloy Repaired by Supersonic Laser Deposition with Laser Shock Peening Treatment

Surface layer properties and fatigue behavior in Al 7075‐T73 and Ti‐6Al‐4V

Effect of ultrasonic peening treatment on the fatigue behaviors of a magnesium alloy up to very high cycle regime

Study on the fatigue performance and Residual Stress of subsurface fluid flow of 2519a aluminum alloy based on water jet peening

Effects of process combinations of milling, grinding, and polishing on the surface integrity and fatigue life of GH4169 components

Fatigue performance improvement of laser shock peened hole on powder metallurgy Ni-based superalloy labyrinth disc