Abstract:Sn-Zn system and Sn-Ag-Cu system solders have been supposed as promising lead-free solders. In this work, the shear strength and fracture mechanism of Sn-9Zn-2.5Bi-1.5In and Sn-3Ag-0.5Cu pastes joints with Cu substrates under the conditions of aging treatment was studied. It is indicated that the intermetallic compounds (IMC) in SnAgCu/Cu joints surfaces are scalloped Cu6Sn5 and planar Cu3Sn. And the IMC in SnZn/Cu joints are Cu5Zn8 layers. In both solder joints, the cracks tend to transform from solder-fracture model to the solder/IMC interface-fracture model with aging treatment. In SnAgCu joints, Cu6Sn5 scallops grew larger and Cu3Sn layer thickened owing to the continuous interdiffusions of Cu and Sn atoms. More Kirkendall-voids appeared in the Cu3Sn layer, and cracks expanded at the interface. Then, the joints would tend to fracture at the solder/IMC interface or in the IMC layer, and the joint strength decreased. However, the situation is different for SnZn joints with aging treatment. In the as-reflowed joints, fracture mainly occurred in the solder matrix. As aging time increased, little zinc could react with copper, which brought out a slow growth rate of Cu5Zn8 IMC. When the aging time increased to 168h, obvious diffusion channels between Cu5Zn8 IMC interface layer and Zn-phase in solder can be observed, and therefore, many Zn-phases reacted with Cu to form Cu5Zn8 IMC in the solder matrix. The different diffusion velocities of Cu and Zn could result in voids at the interface, and then fractures tend to expand along the interface. In summary, both solder joints as reflowed mainly showed ductile fracture mode in the solder, while the shear strength of SnZn joints is 64MPa, higher than the 56MPa of SnAgCu joints. As aging time increased, the shear strength of SnZn joints reduced slightly to 60MPa when the time is 48h, then dropped 30% to 45MPa when the time is 168h, and finally stayed above 40MPa until 720h. As for SnAgCu joints, the shear strength decreased from 56MPa to 45MPa until 168h, and finally dropped about 40% to 35MPa until 720h.

Shear Strength of Joints Fabricated by Solders with High Indium Content

Experimental and Statistical Study of the Fracture Mechanism of Sn96.5Ag3Cu0.5 Solder Joints via Ball Shear Test

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Comparison of high-speed shear properties of low-temperature Sn-Bi/Cu and Sn-In/Cu solder joints

Shear Strength and Fracture Analysis of Sn-9Zn-2.5Bi-1.5In and Sn-3.0Ag-0.5Cu Pastes with Cu-substrate Joints under Different Reflow Times

Research on joining metal-ceramics composite Al/Al2O3 with Cu substrate using solder type Zn–In–Mg

First-principles calculation of the effects of In doping on η-Cu 6 Sn 5 structure, elastic anisotropy, electronic properties and fracture toughness

The Study Into the Transition Areas of a Soldered Joint of ito Ceramics

Dependence of the microstructure and properties of joints on acoustic intensity during the ultrasonic soldering of 7075 Al alloys

Microstructure, elastic modulus and shear strength of alumina (Al2O3) nanoparticles-doped tin–silver–copper (Sn–Ag–Cu) solders on copper (Cu) and gold/nickel (Au/Ni)-plated Cu substrates

A Study of the Interface of Soldered Joints of SnInAgTi Active Solder with Ito Ceramics

Joining Si3N4 ceramic to Invar using Mo mesh and Cu foil interlayer

Effect of Nickel, Tin, and Indium Doping of the Eutectic Silver–Copper Filler on the Capillary and Contact Processes in Brazing of Nonmetallic Alumina-Based Materials with Titanium

Contrastive Study on Shear Strength and Fracture Mechanism of Sn-9Zn-2.5Bi-1.5In and Sn-3.0Ag-0.5Cu Solder Joints with Aging Treatment

Study on Shear Strength for Sn-3Ag-3Bi Solder Joint

Microstructure and Mechanical Properties of Resistance Heat-Assisted High-Power Ultrasonic Dissimilar Welded Cu/Al Joint

Avoiding degradation and increasing joint strength of Al alloys by rapid ultrasonic soldering at low temperature

Microstructure evolution and grain refinement of ultrasonic-assisted soldering joint by using Ni foam reinforced Sn composite solder

Thermal Property, Wettability and Interfacial Characterization of Novel Sn–Zn–Bi–In Alloys As Low-Temperature Lead-Free Solders

Application of Ultrasonic Power in Forming Sn58Bi/Cu Solder Joints with Trace Si3N4 Nanowire Doping