Abstract:Legislations concerning emissions from heavy-duty diesel engines are becoming increasingly stringent. This requires conventional diesel combustion to be compliant using costly and sophisticated aftertreatment systems. Preferably, diesel–methanol dual-fuel is one of the suitable alternative combustion modes as it can potentially reduce the formation of nitrogen oxide and soot emissions which characterised the diesel mixing-controlled combustion. This is primarily due to the high latent heat of vaporisation and oxygen content of the methanol fuel. At high engine loads, however, the potential of diesel–methanol dual-fuel operation is constrained by the excessive combustion pressure rise rate and peak in-cylinder pressure, which limits both the engine efficiency and the percentage of methanol that can be used. For the first time, experimental studies were conducted to explore advanced combustion control strategies such as Miller cycle, exhaust gas recirculation, and intake air cooling for improving upon high load diesel–methanol dual-fuel combustion. Experiments were carried out at 1200 r/min and 18 bar indicated mean effective pressure on a single-cylinder heavy-duty diesel engine, which equipped with a high pressure common rail diesel injection, a methanol port fuel injection, and a variable valve actuation system on the intake camshaft. Results showed that the methanol energy fraction of a conventional diesel–methanol dual-fuel operation with a baseline intake valve closing timing was limited to 28%. This was due to the high combustion temperature at a high load which advanced the ignition timing of the premixed charge, resulting in high levels of pressure rise rate. The application of lower effective compression ratio and intake air temperature ( T int ) effectively decreased the compression temperature, which successfully delayed the ignition timing of the premixed charge. This allowed for a more advanced diesel injection timing to achieve improvement in the thermal efficiency and potentially enabled a higher methanol substitution ratio. Although the introduction of exhaust gas recirculation demonstrated very slight impact on the ignition timing of the premixed charge, a higher net indicated efficiency was observed due to a relatively lower local combustion temperature which reduced heat transfer loss. Moreover, the optimised diesel–methanol dual-fuel operation allowed a higher methanol energy fraction of 40% to be used at an effective compression ratio of 14.3 and T int of 305 K and achieved the highest net indicated efficiency of 47.4%, improving by 3.7% and 2.6%, respectively, when compared to the optimised conventional diesel combustion (45.7%) and conventional diesel–methanol dual-fuel (46.2%). This improvement was accompanied with a reduction of 37% in nitrogen oxide emissions and little impact on soot emissions in comparison with the conventional diesel combustion.

Performance and emissions of a high-speed marine dual-fuel engine operating with methanol-water blends as a fuel

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Study of Effects on Performances and Emissions of a Large Marine Diesel Engine Partially Fuelled with Biodiesel B20 and Methanol

A preliminary numerical study on the use of methanol as a Mono-Fuel for a large bore marine engine

Numerical Study of the Effect of Direct-Injection Timing of Methanol and Excess Air Ratio on the Combustion Characteristics of a Marine Diesel-Methanol Dual-Fuel Engine

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Combustion and Emission Characteristics of Methanol–Diesel Dual Fuel Engine at Different Altitudes

A comparative study of combustion and emission characteristics of dual-fuel engine fueled with diesel/methanol and diesel–polyoxymethylene dimethyl ether blend/methanol

Performance optimization of a diesel engine fueled with hydrogen/biodiesel with water addition based on the response surface methodology

Effects of Methanol Addition on the Combustion Process of the Methanol/Diesel Dual-Fuel Based on an Optical Engine

Experimental study on the effects of water addition in methanol on the performance of diesel-methanol diffusion combustion on a high-speed engine

Role of the Compression Ratio in Dual-Fuel Compression Ignition Combustion with Hydrogen and Methanol

Experimental investigation of emissions from a single-cylinder diesel engine using methanol–diesel blends

Investigation on efficient and clean combustion pre-injection strategy of a diesel/methanol dual direct-injection marine engine under full load

Multi-objective optimization of the performance for a marine methanol-diesel dual-fuel engine

Exploring the high load potential of diesel–methanol dual-fuel operation with Miller cycle, exhaust gas recirculation, and intake air cooling on a heavy-duty diesel engine

Numerical study of injection strategies for marine methanol/diesel direct dual fuel stratification engine

Experimental Investigation on the Emissions of a Port Fuel Injection Spark Ignition Engine Fueled with Methanol–Gasoline Blends

Experimental investigation on exhaust emissions of a heavy-duty vehicle powered by a methanol-fuelled spark ignition engine under world Harmonized Transient Cycle and actual on-road driving conditions

Optimization of methanol/diesel dual-fuel engines at low load condition for heavy-duty vehicles to operated at high substitution ratio by using single-hole injector for direct injection of methanol