Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Cellulose-Encapsulated Composite Electrolyte Design: Toward Chemically and Mechanically Enhanced Solid-Sodium Batteries

Ionic Liquid Reinforced NaSICON-type Oxide Electrolyte Films Enabling Solid State Conversion Metal Fluoride-Lithium Batteries

A Cellulose Encapsulated Composite Electrolyte Design: Towards Chemically and Mechanically Enhanced Solid-sodium Batteries

(Invited) Sulfide-Based Solid Electrolytes for Solid State Batteries

Self‐Templated 3D Sulfide‐Based Solid Composite Electrolyte for Solid‐State Sodium Metal Batteries

Ultrathin Salt-Free Polymer-in-ceramic Electrolyte for Solid-State Sodium Batteries

A Self‐Forming Composite Electrolyte for Solid‐State Sodium Battery with Ultralong Cycle Life

Liquid-phase sintering enabling mixed ionic-electronic interphases and free-standing composite cathode architecture toward high energy solid-state battery

In Situ Polymerization on a 3D Ceramic Framework of Composite Solid Electrolytes for Room‐Temperature Solid‐State Batteries

Flexible Composite Solid Electrolyte with 80 Wt% Na3.4Zr1.9Zn0.1Si2.2P0.8O12 for Solid-State Sodium Batteries

High Energy Density Solid State Lithium Metal Batteries Enabled by Sub‐5 Μm Solid Polymer Electrolytes

Ultra‐Thin Single‐Particle‐Layer Sodium Beta‐Alumina‐Based Composite Polymer Electrolyte Membrane for Sodium‐Metal Batteries

Composite Electrolytes and Interface Designs for Progressive Solid‐state Sodium Batteries

A composite electrolyte based on aluminum oxide filler/polyester polymer via in situ thermal polymerization for long-cycle sodium metal batteries

Constructing High Performance Dry-Processing Oxide Composite Electrolyte Via Interfacial Interactions for Durable Solid-State Lithium Batteries

Si3N4-Assisted Densification Sintering of Na3Zr2Si2PO12 Ceramic Electrolyte toward Solid-State Sodium Metal Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

A Stable Cathode-Solid Electrolyte Composite for Long-Cycle-Life, High Voltage Solid-State Sodium-ion Batteries

Cathode Structural Design Enabling Interconnected Ionic/electronic Transport Channels for High-Performance Solid-State Lithium Batteries

Interface Ionic/Electronic Redistribution Driven by Conversion‐Alloy Reaction for High‐Performance Solid‐State Sodium Batteries

A stable cathode-solid electrolyte composite for high-voltage, long-cycle-life solid-state sodium-ion batteries