Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Accelerating polysulfides conversion by constructing Lewis acidic Mn-N 4 single atomic sites for Li-S battery with high sulfur loading

Selective Adsorption and Electrocatalysis of Polysulfides Through Hexatomic Nickel Clusters Embedded in N-Doped Graphene Toward High-Performance Li-S Batteries

O-, N-Coordinated single Mn atoms accelerating polysulfides transformation in lithium-sulfur batteries

Modulating the d-band center of single-atom catalysts for efficient Li2S2-Li2S conversion in durable lithium-sulfur batteries

Fast conversion and controlled deposition of lithium (poly)sulfides in lithium-sulfur batteries using high-loading cobalt single atoms

N, S‐Coordinated Co Single Atomic Catalyst Boosting Adsorption and Conversion of Lithium Polysulfides for Lithium‐Sulfur Batteries

Accelerated Polysulfide Conversion by Rationally Designed NiS2‐CoS2 Heterostructure in Lithium–Sulfur Batteries

Accelerated Polysulfide Conversion on Hierarchical Porous Vanadium-Nitrogen-carbon for Advanced Lithium-Sulfur Batteries.

A Transmetalation Synthetic Strategy to Engineer Atomically Dispersed MnN 2 O 2 Electrocatalytic Centers Driving High‐Performance LiS Battery

Tuning Dual-Atom Mediator Toward High-Rate Bidirectional Polysulfide Conversion in Li-S Batteries

Strong Lithium Polysulfide Chemisorption on Electroactive Sites of Nitrogen-Doped Carbon Enables High-Performance Lithium-Sulfur Battery Cathodes

Nonmetallic‐Bonding Fe–Mn Diatomic Pairs Anchored on Hollow Carbonaceous Nanodisks for High‐Performance Li–S Battery

Enhanced Polysulfide Regulation <i>via</i> Porous Catalytic V<sub>2</sub>O<sub>3</sub>/V<sub>8</sub>C<sub>7</sub> Heterostructures Derived from Metal-Organic Frameworks toward High-Performance Li-S Batteries

Facilitation polysulfides adsorption/catalysis by nitrogen/phosphorous co-doped carbon nanofibers networks for advanced lithium/polysulfides batteries

Rich Heterointerfaces Enabling Rapid Polysulfides Conversion and Regulated Li2S Deposition for High-Performance Lithium-Sulfur Batteries.

Promoting polysulfide conversions via cobalt single-atom catalyst for fast and durable lithium-sulfur batteries

A unique three-dimensional network double-core-shell structure S@MnO2@MXene suppresses the shuttle effect in high-sulfur-content high-performance lithium-sulfur batteries

Constructing MoS 2 -SnS heterostructures on N-doped carbon nanosheets for enhanced catalytic conversion of polysulfides in lithium-sulfur batteries

Nickel Single Atom Overcoordinated Active Sites to Accelerate the Electrochemical Reaction Kinetics for Li-S Cathode

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Mastering Surface Sulfidation of MnP‐MnO2 Heterostructure to Facilitate Efficient Polysulfide Conversion in Li─S Batteries