Abstract:While the use of a Zn interlayer has been demonstrated to reduce the temperature required for joining easily oxidized metal alloys in atmospheric environments, the effects of reactions between the titanium alloy work pieces and the Zn interlayer on the mechanical performance of the finished joints are poorly understood. The present work addresses this issue by evaluating the chemical compositions at the interfaces of pre-galvanized Ti6Al-4 V alloys joined at 420 ? in an atmospheric environment by ultrasonic-assisted brazing, and relating the observed compositions to the mechanical performances of the joints. The Ti-6Al-4 V alloy workpieces are first wetted by pure Zn using an ultrasonic assisted hot dip galvanizing (U-HDG). The obtained ultrasonic excitations are demonstrated to destroy the oxide film on the surfaces of the Ti-6Al-4 V workpieces and promote reactions between Ti and Zn at the interfaces. The plating of Zn on the workpiece surfaces is demonstrated to be realized by the formation of intermetallic compounds (IMCs) comprising a uniform TiZn3 layer in contact with the Ti-6Al-4 V surface, followed by a mixed TiZn3 + TiZn16 layer and a 1-Zn layer at the outer surface. Application of the ultrasonic-assisted brazing process is demonstrated to maintain uniform TiZn3 layers next to the Ti-6Al-4 V surfaces, while the concentration of the TiZn16 phase near the midpoint of the joints increases with increasing ultrasonic treatment time (UST) from 5 s to 20 s, and the corresponding concentration of the 1-Zn phase decreases. The results of mechanical testing demonstrate that the shear strength of the joint obtained with a TiZn3 layer thickness of 8-12 mu m and a UST of 10 s is 210 MPa, which is 3.55 times greater than that obtained for joints processed without pre-galvanization.

Fabrication and characterization of zinc-coated aluminum particle joining materials via zincate treatment

Fabrication of Nanocrystalline Zro2 Particle Reinforced Aluminum Alloy Composite by Squeeze Casting Route

The Effect of a Zinc Interlayer on the Microstructure and Mechanical Properties of a Magnesium Alloy (AZ31)–Aluminum Alloy (6060) Joint Produced by Liquid–Solid Compound Casting

Effects of TiZn3 and TiZn16 Components on the Microstructure and Mechanical Performance of Ti-6Al-4 V Alloy Joints Formed Via Ultrasonic Assisted Brazing Using Pre-Galvanized Workpieces.

Preparation of Zn-based Alloy Filler for Brazing Aluminum and Microstructure and Shear Strength of Brazed Joint

Effect of a Zn interlayer on the formation mechanism and mechanical of AA6061/DP590 steel resistance

Joining Mg Alloys with Zn Interlayer by Novel Ultrasonic-Assisted Transient Liquid Phase Bonding Method in Air

Effect of a Zn interlayer on the formation mechanism and mechanical performance of AA6061/DP590 steel resistance riveting welding

Joining of Magnesium and Aluminum Via Arc-Assisted Ultrasonic Seam Welding with Sn/Zn Composite Interlayer

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Effects of material combination for ultrasonic spot welding on microstructure and strength of Al/Al, Al/Cu, and Al/Ni dissimilar joints

Interfacial Microstructure and Mechanical Properties of Al/steel Joints Fabricated Via Thermo-Compensated Resistance Brazing Welding with Cold Spray Zn Interlayer

Microstructure and Mechanical Performance of AZ31/2024 Dissimilar Alloy Joints Using a Multi-Interlayer of Ni/Al/Zn Via Ultrasonic-Assisted Transient Liquid Phase Bonding

Joining of Cf/Al Composites and TiAl Intermetallics by Laser-Induced Self-Propagating High-Temperature Synthesis Using the Ni-Al-Zr Interlayer

Joining mechanism, microstructure, and mechanical properties of AZ31/6061 joint prepared by pouring fusion welding process assisted with Zn-xSn brazing filler

Effects of Zn on Intermetallic Compounds and Strength of Al/Mg Joints Ultrasonically Soldered in Air

Mechanical Behavior and Microstructure of Ultrasonic-Spot-Welded Al/Cu Dissimilar Joints with Zn Interlayer

Effect of the Microstructure of IMCs and Zinc Accumulation on the Mechanical Properties of Aluminum/galvanized Steel Joints in the VP-CMT Process

Dissimilar ultrasonic spot welding of rare-earth containing ZEK100 magnesium-to-aluminum alloy with a zinc interlayer: Microstructural evolution and mechanical properties

Si Particulate-Reinforced ZnAl Based Composites Joints of Hypereutectic Al50Si Alloys by Ultrasonic-Assisted Soldering

Mechanical properties and microstructure analysis of welding-brazing of Al/ti butt joint with Zn foil additive