Abstract:Stereolithography (SLA) additive manufacturing is a method of manufacturing capable of generating complex geometric shapes with extremely high accuracy. Classic SLA uses UV curable resins, particularly polylactic acid (PLA), for part generation, but recent research has focused on utilizing this technology for the generation of various composite materials. There has been success in manufacturing composite materials using this technology, but little research has been performed on the generation of carbon-fiber-reinforced composite materials. Carbon fiber stereolithography (CF-SLA) is often overlooked due to carbon fiber's natural inability to bond with PLA. To overcome this boundary, surface modification techniques were used on chopped carbon fibers to achieve greater bonding. Here, two modification techniques were explored: a sodium dodecyl sulfate (SDS) surfactant addition and nitric acid (HNO3) etching. These methods were used to functionalize and prepare the surface of chopped carbon fiber (CF) for bonding with cured PLA resin. Treated fibers were dispersed in generic PLA resin, and tensile test specimens were printed for examining the reinforcement potential of the two treatment methods. Additional complexities arise during printing with fibers including fiber alignment, accumulation, and fiber fallout. To address these issues, a novel in-process mixing method was developed to maintain fiber dispersion. A two-level three-factor factorial design was performed for both treatment methods to determine optimal printing parameters. Through mechanical testing, atomic force microscopy, scanning electron microscopy, and contact angle measurements, the accompanying material property changes were characterized to further develop the field of fiber-reinforced liquid crystal display (LCD) additive manufacturing. After testing, it was found that composites created with SDS nanoparticle modification were stronger than both the acid etched fiber sample and plain PLA. Specifically, SDS surface treatment resulted in a 15% increase in modulus and maximum strength of the sample, mainly by enhancing the interlayer bonding between CF and PLA.

Enhanced mechanical properties of the hybrid CFRP-SLA laminates through laminate modifications

Effective mechanisms responsible for increased strength and fracture strain of carbon fiber-reinforced plastic/steel hybrid laminates

Surface topology modification using 3D printing techniques to enhance the interfacial bonding strength between polymer substrates and prepreg carbon fibre-reinforced polymers

Evaluation of Carbon Fiber-Embedded 3D Printed Structures for Strengthening and Structural-Health Monitoring

Enhancing the interfacial bonding strength between 3D-printed aluminium substrates and carbon fibre–reinforced polymers

Self-monitoring Continuous Carbon Fiber Reinforced Thermoplastic Based on Dual-Material Three-Dimensional Printing Integration Process

The Mechanical Properties of Fiber Metal Laminates Based on 3D Printed Composites

Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

Fused-Deposition Modeling 3D Printing of Short-Cut Carbon-Fiber-Reinforced PA6 Composites for Strengthening, Toughening, and Light Weighting

On the Effects of Process Parameters and Optimization of Interlaminate Bond Strength in 3D Printed ABS/CF-PLA Composite

On the bending behavior of hybrid fiber–metal laminates (HFMLs) based on aluminum and glass/Kevlar fibers reinforced epoxy

The Effect of Chopped Carbon Fibers on the Mechanical Properties and Fracture Toughness of 3D-Printed PLA Parts: An Experimental and Simulation Study

Investigating Mechanical Properties of Fabricated Carbon-Fiber-Reinforced Composites via LCD Additive Manufacturing

Correlation between Infill Percentages, Layer Width, and Mechanical Properties in Fused Deposition Modelling of Poly-Lactic Acid 3D Printing

Mechanical characteristics and failure morphology of FFF-printed poly lactic acid composites reinforced with carbon fibre, graphene and MWCNTs

Improving the impact performance of natural fiber reinforced laminate through hybridization and layup design

Property enhancement of 3D printed of timber waste/PLA composite by surface coating

Effects of infill density on mechanical properties of additively manufactured chopped carbon fiber reinforced PLA composites

Blending and functionalisation modification of 3D printed polylactic acid for fused deposition modeling

Mechanical Properties and Characterization of Polylactic Acid/Carbon Fiber Composite Fabricated by Fused Deposition Modeling

Hybrid additive manufacturing of highly sustainable Polylactic acid -Carbon Fiber-Polylactic acid sandwiched composite structures: Optimization and machine learning