Abstract:Abstract At present, there are many studies on the residual stress field and plastic strain field introduced by surface strengthening, which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks. However, there are few studies on the effects of these key factors on fretting wear. In the paper, shot-peening (SP) and ultrasonic surface rolling process (USRP) were performed on Ti-6Al-4V plate specimens. The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer. Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester. The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments. The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation, and the mechanism of improving fretting fatigue life by surface strengthening process was further explained. After USRP treatment, the surface roughness of Ti-6Al-4V is significantly improved. In addition, the microhardness of the specimen after SP reaches the maximum at 80 μm from the surface, which is about 123% higher than that of the AsR specimen. After USRP, it reaches the maximum at 150 μm from the surface, which is about 128% higher than that of AsR specimen. It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction, and the residual stress reaches the maximum on the sub surface. The USRP specimen reaches the maximum value at 0.18 mm, about − 550 MPa, while the SP specimen reaches the maximum value at 0.1 mm, about − 380 MPa. The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP. The surface integrity of specimens after USRP is the best, which has deeper residual compressive stress layer and more refined grain. In this paper, a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.

Study on bending fretting fatigue behaviour of 15-5PH stainless steel with different fretting regimes

Effects of low-cycle fatigue on static mechanical properties, microstructures and fracture behavior of 304 stainless steel

Investigation on Fatigue Strength and Notch Effect of 17-4PH Blade Root

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

Wear- and Surface-Fatigue-Mediated Damage During Fretting in a High-Strength Titanium Alloy

Experimental and Numerical Investigations of Fretting Fatigue Behavior for Steel Q235 Single-Lap Bolted Joints

In-situ Observation and Finite Element Analysis of Fretting Fatigue Crack Propagation Behavior in 1045 Steel

The strain ratio-dependent multiaxial low cycle fatigue behaviour and life prediction of 316L stainless steel based on critical plane at elevated temperature

Experimental and finite element analysis for evaluating influence of contact pressure on fretting fatigue mechanisms of A319‐T6 cast aluminum alloy

Bending fatigue behavior of metastable and stable austenitic stainless steels with different surface morphologies

Fretting fatigue crack initiation and propagation behaviours of Ti6Al4V alloy coated by functionally graded material

Ultra-high Cycle Fatigue Fracture Mechanism of a Precipitation HardeningStainless Steel at Different Stress Ratios

Influence of Ultrasonic Surface Rolling Process and Shot Peening on Fretting Fatigue Performance of Ti-6Al-4V

Cyclic deformation mechanism and fracture behaviour of 316L stainless steel under thermomechanical fatigue loading

Failure Mechanism Research on Bending Fretting Fatigue of 6061-T6 Aluminum Alloy by Experiment and Finite Element Method

Fretting Fatigue Damage Behavior of TC4 Alloy

Study on fretting fatigue behavior of TC4 titanium alloy

Fretting Fatigue Behavior and Damage Mechanism of Cast Al-Si-Cu-T6 Alloy Under Two Surface Roughness conditions

Numerical Investigation of Fatigue Crack Propagation Behaviour of 550E High-Performance Steel

Fracture Behavior of PH 15-5 Stainless Steel Manufactured via Directed Energy Deposition

Bending Fatigue Behavior of 316L Stainless Steel up to Very High Cycle Fatigue Regime