Abstract:The existing image-free Total Hip Arthroplasty (THA) navigation systems conventionally utilise the patient-specific Anterior Pelvic Plane (APP) as the reference to calculate orientations of the implanted cup, e.g. anteversion and inclination angles. The definition of APP relies on the intra-operative digitisation of three anatomical landmarks, the bilateral Anterior Superior Iliac Spine (ASIS) and the pubicum. Due to the presence of the thick soft tissue around the patient's pubic region, however, the landmark on pubic area is hard to be digitised accurately. A novel reference plane called Intra-operative Reference Plane (IRP) was proposed by G. Zheng et al to address this issue. To determine the IRP, bilateral ASIS and the cup center of the operating side instead of the pubicum are digitised intra-operatively. It avoids the error-prone digitisation of pubicum, and the angle between the patient-specific APP and the suggested IRP can be computed pre-operatively by a single X-ray radiograph-based 2D/3D reconstruction approach developed by G. Zheng et al. Based on this angle, the orientation of the APP can be intra-operatively estimated from that of the IRP such that all measurements with respect to IRP can be transformed to measurements with respect to APP. In order to implement and validate this new reference plane for image-free navigation of acetabular cup placement, we developed an IRP-based image-free THA navigation system. All cup placement instruments were mounted with passive markers whose positions could be traced by a NDI Polaris® infrared camera (Northern Digital Inc, Ontario, Canada). The cup center was obtained by first pivoting a tracked impactor with appropriate size of the mounted trial cup and then calculating the pivoting center through a least-squares fitting. The bilateral ASIS landmarks were acquired through the percutaneous pointer-based digitisation. We tested this new IRP-based image-free THA navigation system in our laboratory by conducting twelve studies on two dry cadaver pelvises and two plastic pelvises. The ground truth for each study was established using the conventional APP-based method, i.e., in addition to those landmarks required by our IRP-based method, we also digitised the pubicum on respective pelvic bones and calculated cup orientations on the basis of the digitised APP. The mean and standard deviation of differences between the proposed IRP-based anteversion measurement and the ground truth are 1.0 degree and 0.7 degree, while the maximal and minimal differences are 2.1 degree and 0.3 degree respectively. The mean and standard deviation of differences between the proposed IRP-based inclination measurement and the ground truth are respective 0.2 degree and 0.2 degree. Moreover, the maximum of differences is 0.5 degree and the minimum is 0.0 degree. Our laboratory experimental results demonstrate that the new IRP-based image-free navigation system is accurate enough for acetabular cup placement. In comparison to existing image-free navigation systems that use APP as the reference plane, the newly developed system employs IRP as the reference plane, which has the advantage to eliminate the digitisation of landmarks around the pubic region. The successful validation with the laboratorial study has led us to the next step of clinical trials. We expect to report preliminary clinical cases in the near future.

Smart Acetabular Trail With Embedded Photonic Sensor Arrays for Force and Contact Location Sensing

All-fiber optic displacement sensing system for an Ilizarov transverse tibial bone transport device.

Tuberosity reconstruction baseplate for shoulder hemiarthroplasty: Morphological design and biomaterial application

Smart Trail with Camera and Inertial Measurement Unit for Intraoperative Estimation of Hip Range of Motion in Total Hip Replacement Surgery.

Laser Direct‐Write Sensors on Carbon‐Fiber‐Reinforced Poly‐Ether–Ether–Ketone for Smart Orthopedic Implants

Orientation and Depth Estimation for Femoral Components Using Image Sensor, Magnetometer and Inertial Sensors in THR Surgeries.

Laser Direct-Write Sensors On CFR-PEEK For Smart Orthopedic Implants

Sensitivity‐Enhanced Skin‐Attachable Strain Sensors Using Multi‐Material Printed Bioinspired Heterogeneous Moduli Structures for Proprioceptive Training

Photocurable Polymer-Based 3D Printing: Advanced Flexible Strain Sensors for Human Kinematics Monitoring

Interfacial load monitoring and failure detection in total joint replacements via piezoresistive bone cement and electrical impedance tomography

VALIDATING A NEW REFERENCE PLANE FOR IMAGE-FREE NAVIGATION OF ACETABULAR CUP PLACEMENT

Artificial intelligence assisted preoperative planning and 3D-printing guiding frame for percutaneous screw reconstruction in periacetabular metastatic cancer patients

Semi-automated finite element analyses of surgically treated acetabular fractures to investigate the biomechanical behaviour of patient-specific compared to conventional implants

Kinematic-kinetic compliant acetabular cup positioning based on preoperative motion tracking and musculoskeletal modeling for total hip arthroplasty

Development of the Force Detecting Liner for Total Knee Arthroplasty

Development of a Flexible Meniscus Sensor for Detection of Force Distribution in Knee Arthroplasty

Biomechanical analysis and clinical observation of 3D-printed acetabular prosthesis for the acetabular reconstruction of total hip arthroplasty in Crowe III hip dysplasia

Remote Analysis of Femoroacetabular Impingement by a triade of label-free optical spectroscopy techniques

An IMU-Based Real-Time Measuring System for Acetabular Prosthesis Implant Angles in THR Surgeries

Development and validation of a 3D-printed interfacial stress sensor for prosthetic applications

Wearable bio-adhesive metal detector array (BioMDA) for spinal implants