Abstract:Carbon fiber reinforced polymer (CFRP) and titanium alloy (Ti-6Al-4V) have excellent mechanical properties and have been widely used in aviation, aerospace, and other fields. Due to the different characteristics of CFRP/Ti-laminated materials, there are differences in their processing parameters and material removal methods. Cutter wear and hole defects are prone to occur. To study the cutting performance of cutters in laminated materials, this paper adopts the inclined angle milling method to process CFRP/Ti-laminated materials. The cutting performance of flat end milling cutter and circular arc milling cutter was compared and analyzed through designed variable parameter experiments. A study was conducted on the axial force, cutter wear mechanism, hole quality, and micro-morphology of the hole wall of two cutters under the inclined angle milling method. The results show that under different processing parameters, the difference in axial force between the two cutters is small in the carbon fiber layer. However, there is a significant difference in the titanium layer, with the axial force of the circular arc milling cutter being smaller than that of the flat end milling cutter. As the number of holes increases, the wear of the flat end milling cutter is serious, and the cutting edge is broken. The wear area gradually expands from the cutter tip to the surrounding cutting edge. The wear of the circular arc milling cutter is relatively light, and the cutting edge is damaged. As the wear at the arc transition becomes dull, the wear area gradually extends to the surrounding cutting edge. As the cutters wear out, many burrs and tear damage appear at the CFRP exit of the flat end milling cutter. Many high burrs appeared at the exit of Ti-6Al-4V. Comparing the micro-morphology of the hole wall of the two cutters at different fiber cutting angles, the quality of the hole wall of the flat end milling cutter is worse than that of the circular arc milling cutter. Due to the arc transition structure of the circular arc milling cutter, the hole wall has obvious groove scratches, resulting in a decrease in the quality of the Ti-6Al-4V hole wall. In addition, compared with the flat end milling cutter, the surface roughness of the hole of the circular arc milling cutter is better.

Study on parametric design and cutting performance of double-arc milling cutter

Machining Parameter Optimization of Milling Process Based on Uniform Design

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Study on design of conical arc side-edge milling cutter and cutting performance under ultrasonic-assisted condition

Research and development of parametric design platform for series complex cutting tools

Comprehensive Evaluation Analysis and Optimization Methodology of Tool Geometric Parameters for High Speed Cutting

Research on design and cutting performance of revolving lemniscate milling cutter

Analysis of Multi-Objective Optimization of Machining Allowance Distribution and Parameters for Energy Saving Strategy

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

The Dynamic Comprehensive Evaluation of the Importance of Cutting Parameters in the Side Milling TC4 Process Using an Integrated End Mill

Development and application of parametric design system for solid end mills based on Open CASCADE

Research on Force-Saving Mechanism of Cutting Tool with Variable Curvature Directrix Rake Face Configuration

Suppressing the burr of high aspect ratio structure by optimizing the cutting parameters in the micro-milling process

Simulation and Experimental Study on the Effect of Edge Radius on the Cutting Condition of Carbide Inserts

Accurate 3-D Parameterised Modelling of Complex Milling Cutter with Fir-Slots for Rotor-Groove Machining

Analysis and Optimization of Parameters of Machine Tool in Structure Design Based on the Cutting Dynamics with Uncertainty

A Computer Aided Tool Selection System For 3d Die/Mould-Cavity Nc Machining Using Both A Heuristic And Analytical Approach

Parameter optimization of ball-end milling cutter with blunt-round edge and micro-texture on flank

Iterative Generation Method of Arc Length Parameterized Curve Tool Path for Surface Machining from Short-Line Tool Path

Comparative study on cutting performance of CFRP/Ti-laminated materials with flat end milling cutter and circular arc milling cutter in inclined angle milling