Abstract:Continuous basalt fiber (CBF) is a new type of performance outstanding inorganic nonmetallic material. In comparison with carbon fibers, basalt fibers exhibit greater failure strain as well as better impact and fire resistance with less poisonous fumes and 50% cost reduction. It is also known that basalt fibers display higher mechanical properties, better chemical stability and superior thermal and electrical insulation as compared with glass fibers. Basalt fiber has been widely used as a reinforcing composite material for construction industry and for preparation of polymer matrix composites. As high-performance low-cost reinforcements, basalt fibers should have a great potential for strengthening metal matrix composites (MMCs) and reducing their preparation cost. However, so far, few reports focused on the investigation on metal matrix composites reinforced by continuous basalt fibers, especially for lack of feasible fabrication technologies. Thus, in the present work, two-dimensional continuous basalt fiber cloth and Al12Si alloys foils were selected as raw materials and alternately stacked to obtain a sandwiched structure. Subsequently, vacuum pressure infiltration was utilized to fabricate aluminum matrix composites reinforced by continuous basalt fibers (CBF/Al) with volume fraction of 65% successfully. Influence of infiltration parameters on microstructure evolution of resulting aluminum matrix composites was investigated and formation mechanism of multi-layered structure of CBF/Al composite was clarified. Moreover, mechanical properties of the multi-layered CBF/Al composite were evaluated. The results showed that when the infiltration parameters were 660., 10 MPa and 10 min, fully dense CBF/Al composite could be achieved and the novel composite displayed a unique multi-layered structure, namely continuous basalt fibers in forms of cruciform crossing distributed within aluminum alloys matrix. It is noteworthy that no obvious chemical reaction happened between continuous basalt fibers and Al-12Si alloys, and sound metallurgical bonding interface between them was obtained due to the interdiffusion of Al and Si elements. Unfortunately, mechanical properties of multi-layered CBF/Al composite did not reach a desired level, which was attributed to (i) decreasing of effective load-carrying capacity due to the imperfect distribution manner of continuous basalt fibers and (ii) deteriorating of intrinsic mechanical properties at high temperature.

Fabrication and characterization of layered structure reinforced composite metal foam

Crushing Behavior of Multi-Layer Metal Lattice Panel Fabricated by Selective Laser Melting

Improved Manufacturing Method and Mechanical Performances of Carbon Fiber Reinforced Lattice-Core Sandwich Cylinder

Fabrication and Mechanical Characteristics of Multi-Laminated Aluminum Matrix Composites Reinforced by Continuous Basalt Fibers

Fabrication Process, Tensile, and Gamma Rays Shielding Properties of Newly Developed Fiber Metal Laminates Based on an Al–Li Alloy and Carbon Fibers‐Tungsten Carbide Nanoparticles Reinforced Phthalonitrile Resin Composite

Mechanical properties of a novel fiber metal laminate based on a carbon fiber reinforced Zn-Al alloy composite

A novel bio-inspired metal hollow sphere filled TC4/Al sandwich composite: Fabrication and compressive properties

Manufacturing and Testing of a CFRC Sandwich Cylinder with Kagome Cores

Fabrication and Mechanical Characterization of CFRP X-core Sandwich Panels

Fabrication and mechanical properties of novel CFRP/Mg alloy hybrid laminates with enhanced interface adhesion

Preparation and characterization of light weight aluminum matrix syntactic foams with high energy absorbing capacity

Design and Manufacturing of a Composite Lattice Structure Reinforced by Continuous Carbon Fibers

Multi‐layer structure design, fabrication and numerical simulations of 3D woven spacer fabric composites with improved mechanical properties

Mechanical behavior of carbon fiber composite lattice core sandwich panels fabricated by laser cutting

Improvement of compressive property and damping capacity of multilayer aluminum matrix foams with 316 L hollow spheres and NiTi alloy sheets

Interface characterization and mechanical property of an aluminum matrix syntactic foam with multi-shelled hollow sphere structure

An Interactive Fluid–Solid Approach for Numerical Modeling of Composite Metal Foam Behavior under Compression

Investigation of structure–flexural response relations in thermoplastic carbon/glass fiber‐metal laminates

Evaluation Of Nano-Mechanical Behavior On Flax Fiber Metal Laminates Using An Atomic Force Microscope

Fabrication and Compressive Behavior of Carbon-Fiber-reinforced Cylindrical Foldcore Sandwich Structure

Mechanical properties study on sandwich hybrid metal/(carbon, glass) fiber reinforcement plastic composite sheet