Abstract:Lithium–sulfur (Li–S) batteries are regarded as one of the most promising next-generation battery technologies owing to their ultrahigh energy density up to 2600 W h kg–1 and low cost. However, major challenges still remain in the application of Li–S batteries, such as shuttle effect and sluggish redox kinetics. Herein, it is demonstrated that phosphorus doping can not only significantly improve the polysulfide adsorption but also enhance the catalysis effects of metal–organic framework-derived CoS2 nanoboxes in Li–S batteries. Consequently, a modified separator integrated with P–CoS2 and carbon nanotubes effectively suppresses the polysulfide shuttle and propels the redox kinetics of polysulfides, thus promising higher specific discharge capacity, better rate, and stable cycle performance. Even under the high sulfur loading condition (4.8 mg cm–2), the areal discharge capacity of the cell with the functional separator can still remain at 4.5 mA h cm–2 after 100 cycles at 0.2 C. More importantly, this work may encourage more effort on anion doping for engineering the polar surface of transition-metal compounds to further mediate the interfacial redox chemistry between transition-metal compounds and polysulfides in Li–S batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c00494?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c00494</a>.XRD patterns, SEM, TEM images of Co–MOF and CoS2; high-magnification XRD patterns of CoS2 and P-CoS2 in the 2θ range of 30–35°; EDS mapping images of CoS2 and P-CoS2; P 2p XPS spectrum of P-CoS2 after etching; SEM images from the front and the cross-section for the CNT-, CoS2/CNT-, and P-CoS2/CNT-modified separator; digital image of the P-CoS2/ separator and folding and unfolding test of the P-CoS2/ separator; permeation tests of the pristine Celgard, , CoS2/, and P-CoS2/ separators; CV curves of symmetric cells of CNTs with and without Li2S6 at 1 mV s–1; galvanostatic discharge/charge curves of P-CoS2/ at 2.0 C; galvanostatic discharge/charge curves and cycling performance of the P-CoS2 cathode without sulfur for the initial few cycles at 0.1 C; postmortem SEM images and EDS analysis of the lithium foil; postmortem SEM images and EDS analysis of CoS2 and P-CoS2 after 1.0 C cycles; and performance statistics of similar Li–S batteries in the literature (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c00494/suppl_file/am1c00494_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Phosphorization-Introduced Defect-Rich Phosphorus-Doped Co 3 O 4 with Propelling Adsorption–Catalysis Transformation of Polysulfide

Phosphorus Vacancies as Effective Polysulfide Promoter for High‐Energy‐Density Lithium–Sulfur Batteries

P-doped Co9S8 nanoparticles embedded on 3D spongy carbon-sheets as electrochemical catalyst for lithium-sulfur batteries

Sequential phosphorization and carbonization with modulated d-p orbital interactions in cobalt phosphides for enhanced polysulfide redox kinetics

Crystalline-amorphous heterostructure on the phosphatized P-CoS 2 /CNT for augmenting the catalytic conversion kinetics of Li-S batteries

Nitrogen-Doped CoP with optimized d-Band center as bidirectional electrocatalyst for high areal capacity of Li-S battery

Phosphorus doping of 3D structural MoS2 to promote catalytic activity for lithium-sulfur batteries

Cation‐Vacancy Engineering Modulated Perovskite Oxide for Boosting Electrocatalytic Conversion of Polysulfides

Defect‐Rich Hierarchical Porous Mn‐Doped CoP Hollow Microspheres Accelerate Polysulfide Conversion

Enhancing Polysulfide Confinement and Electrochemical Kinetics by Amorphous Cobalt Phosphide for Highly Efficient Lithium–Sulfur Batteries

The catalytic role of surface Co(PO3)2 on CoP for high-performance lithium-sulfur batteries

Phosphorous‐Based Heterostructure for the Effective Catalysis of Polysulfide Reactions with Phase Changes in High‐Sulfur‐Loading Lithium–Sulfur Batteries

Phosphorus-Doped Metal–Organic Framework-Derived CoS 2 Nanoboxes with Improved Adsorption-Catalysis Effect for Li–S Batteries

Defect-riched prussian blue analogues with superior adsorption-catalysis toward lithium polysulfides for high performance lithium-sulfur batteries

Defect-Rich Multi-shelled Fe-doped Co3O4 Hollow Microspheres with Multiple Spatial Confinements to Facilitate Catalytic Conversion of Polysulfides for High-Performance Li-S Batteries.

Phosphorus Doped Hierarchical Porous Carbon Nanosheet Array As an Electrocatalyst to Enhance Polysulfides Anchoring and Conversion

Intrinsic catalytic Sites-Rich Co-doped SnO2 nanoparticles enabling enhanced conversion and capture of polysulfides

Oxygen Deficiency Driven Conversion of Polysulfide by Electrocatalysis: MoO3‐x Nanobelts for an Improved Lithium‐Sulfur Battery Cathode

Regulating the phase and catalytic activity of cobalt phosphide based on the morphological engineering of ZIF-67 to enhance the redox kinetics of polysulfides for high-performance lithium-sulfur batteries

In-situ Fabrication of Dense Structure Nitrogen-Doped Carbon Nanotube Embedded Co/Co2P Accelerating the Electrochemical Kinetics of Lithium-Sulfur Battery

Establishing Transition Metal Phosphides as Effective Sulfur Hosts in Lithium–Sulfur Batteries through the Triple Effect of "Confinement–Adsorption–Catalysis"