Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Initial dynamics of irregular eutectic growth under directional solidification

Understanding the Seeded Heteroepitaxial Growth of Crystallizable Polymers: the Role of Crystallization Thermodynamics.

Insights into the Stable Preferred Growth Direction of Rods in the Colony of Al2O3/ZrO2 (Y2O3) Eutectics

From irregular to regular eutectic growth in the Al-Al3Ni system: in situ observations during directional solidification

Global Instabilities of Lamellar Eutectic Growth in Directional Solidification

Eutectic growth in bulk undercooled melts

Morphological Stability of Coupled Growth During Directional Solidification of Eutectic and Peritectic Alloys

Development of Irregular Interface Morphology During Unidirectional Solidification of Succinonitrile

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Revealing the Nucleation and Growth Modes Upon Rapid Solidification of Undercooled Co-24 At.% Sn Eutectic Alloy by the Crystallographic Orientation Relations

Influence of Initial Solid–liquid Interface Morphology on Further Microstructure Evolution During Directional Solidification

Phase-field simulation for the evolution of solid/liquid interface front in directional solidification process

Phase-field simulation of seaweed-like growth morphology of directionally solidified Ni-Cu alloy

Numerical investigation of eutectic growth dynamics under convection by 3D phase-field method

A Steady Solution of the Gasar Eutectic Growth in Directional Solidification

THERMOSOLUTAL CONVECTION DURING DIRECTIONAL SOLIDIFICATION OF Al-Li ALLOYS

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

Influence of interphase anisotropy on lamellar eutectic growth patterns

Liquid migration and peritectic transformation: Investigation on their contributions to growth of peritectic phase in interrupted directional solidification

Effect of Interface Kinetics on the Eutectic Growth

Orientation and Microstructure Evolution of Al-Al 2 Cu Regular Eutectic Lamellar Bifurcating in an Abruptly Changing Velocity under Directional Solidification.