Abstract:Charge accumulation and charged defects at both bulk and buried heterojunction interfaces of perovskites are primarily related to the photovoltaic performance and shelf stability of perovskite solar cells (PSCs). Moreover, detrimental defects distributing along the perovskite bottom side in contact with the tin oxide (SnO2) surface may exert unparalleled significance in charge extraction and transport. Most importantly, interfacial nonradiative recombination can also widely exist, which will seriously hamper efficiency of the related device. In this work, a multifunctional chemical bridge at the perovskite/SnO2 interface is devised through triggering an in situ polymerization strategy, by which cross-linked polymerizable 3-(trimethoxysilyl)propyl methacrylate (MAPS) monomers under the combination of temperature and initiators can form bulkier macropolymers (MAPS dimers). Detailed theoretical and experimental results reveal that the carbonyl groups (CO) of both MAPS monomers and MAPS dimers can chemically anchor to perovskite bottom side through a CO···Pb coordination bond interaction to regulate the film quality and the siloxane groups effectively couple with oxygen vacancies on the SnO2 film surface to facilitate its optoelectronic properties. Compared with the primitive MAPS monomer units, the resultant MAPS dimers simultaneously prevent interfacial charge accumulation and demonstrate a more benign energy level alignment to further augment photovoltaic performance of PSCs. Thus, the devices assembled under open-air conditions based on double-sided passivation deliver a decent photoelectronic performance with the champion efficiency of 20.94% accompanied by negligible hysteresis. Meanwhile, the unencapsulated targeted devices maintain 93.1% and 86.5% of their original efficiency after continuous 500 h thermal treatment and 500 h light illumination under open-circuit conditions, respectively.

Unveiling and Balancing the Passivation‐Transport Trade‐Off in Perovskite Solar Cells with Double‐Side Patterned Insulator Contacts

Dual Role of Rapid Transport and Efficient Passivation in Inverted Methylammonium‐Free Perovskite Solar Cells Utilizing a Self‐Assembled Porous Insulating Layer

Interfacial Passivation of the p-Doped Hole-Transporting Layer Using General Insulating Polymers for High-Performance Inverted Perovskite Solar Cells

A Modulated Double‐Passivation Strategy Toward Highly Efficient Perovskite Solar Cells with Efficiency Over 21%

In Situ Back‐Contact Passivation Improves Photovoltage and Fill Factor in Perovskite Solar Cells

Interfacial Dipole Poly(2-ethyl-2-oxazoline) Modification Triggers Simultaneous Band Alignment and Passivation for Air-Stable Perovskite Solar Cells

Self‐Induced Bi‐interfacial Modification via Fluoropyridinic Acid For High‐Performance Inverted Perovskite Solar Cells

Enhancing Hole Transport Uniformity for Efficient Inverted Perovskite Solar Cells Through Optimizing Buried Interface Contacts and Suppressing Interface Recombination.

Enhanced charge carrier transport and defects mitigation of passivation layer for efficient perovskite solar cells

Direct Observation on <i>p</i>- to <i>n</i>-Type Transformation of Perovskite Surface Region during Defect Passivation Driving High Photovoltaic Efficiency

Reducing nonradiative recombination in perovskite solar cells with a porous insulator contact

Reconfiguration toward Self‐Assembled Monolayer Passivation for High‐Performance Perovskite Solar Cells

Suppressing surface and interface recombination to afford efficient and stable inverted perovskite solar cells

TiO2 surface oxygen vacancy passivation towards mitigated interfacial lattice distortion and efficient perovskite solar cell

Double-Side-Passivated Perovskite Solar Cells With Ultra-Low Potential Loss

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells

Co-passivation of perovskite film towards stable and efficient perovskite solar cell

Effective Passivation with Self‐Organized Molecules for Perovskite Photovoltaics

Bifacial Modified Charge Transport Materials for Highly Efficient and Stable Inverted Perovskite Solar Cells

Synergetic Excess PbI2 and Reduced Pb Leakage Management Strategy for 24.28% Efficient, Stable and Eco‐Friendly Perovskite Solar Cells

Dual-side interfacial passivation of FAPbI3 perovskite film by Naphthylmethylammonium iodide for highly efficient and stable perovskite solar cells