Abstract:Tungsten oxide (WO3) is a strong candidate as the photoanode in photoelectrochemical (PEC) water splitting owing to its moderate band gap (2.6–3.2 eV) for wide light absorption and stable physicochemical properties. This work reports a morphology engineering strategy to fabricate voltage-induced terrace-like tungsten oxide (TW) film and its high-voltage performance as a photoanode for PEC water splitting. By controlling the anodization voltage, the morphology of the anodic WO3 film was altered, and their photoelectrochemical performances were compared. Anodization of the tungsten film in fluoride-containing H3PO4 leads to the growth of either irregular porous tungsten oxide layers or terrace-like tungsten oxide layers, depending on the anodic potentials. The possible growth mechanism of the porous oxide layer during anodization is proposed with a combination of the field-assisted dissolution model and the oxygen-bubble mold model. Under light irradiation, the photocurrent density was 3.0 mA cm–2 at 1.23 V vs RHE (VRHE) for annealed terrace-like WO3, which was almost 3 times larger than that of annealed porous WO3. As a photoanode, terrace-like WO3 films could generate hydrogen at 58 μmol cm–2 h–1 under simulated solar light, while porous WO3 films produced hydrogen with a slower rate of 28 μmol cm–2 h–1. The terrace-like WO3 films experience higher photoelectrochemical performance and incident photon-to-electron conversion efficiency (IPCE) than porous WO3 due to more regular nanostructure, smaller band gap, fast charge-transfer rate, and alleviated recombination rate. This study shows that morphology control can effectively enhance the photocurrent density and IPCE of photoanodes and suggests a practical direction for finding the optimal WO3 films for PEC water splitting.

Investigation of radiation effects on structural, morphological, and compositional properties of WO3 nanostructures for water splitting applications

The Influence of the Structural and Morphological Properties of WO3 Thin Films Obtained by PLD on the Photoelectrochemical Water-Splitting Reaction Efficiency

Nanoporous WO3 Films Synthesized by Tuning Anodization Conditions for Photoelectrochemical Water Oxidation

Tungsten oxide nanostructures and nanocomposites for photoelectrochemical water splitting

Facile Fabrication of Sandwich Structured WO3 Nanoplate Arrays for Efficient Photoelectrochemical Water Splitting.

Influence of Swift Heavy Ion Beam Irradiation on Optical, Structural, and Surface Morphological Properties of WO3 Thin Films Grown by RF Sputtering Method

Photoactive Tungsten-Oxide Nanomaterials for Water-Splitting

High-Voltage Etching-Induced Terrace-like WO 3 Photoanode for Efficient Photoelectrochemical Water Splitting

Gamma Ray Radiation Effect on Bi2WO6 Photocatalyst

Γ-Radiation Effects on Metal Oxide Particles and Their Wetted Surfaces

Enhancement of the Photoelectrochemical Performance of WO3 Vertical Arrays Film for Solar Water Splitting by Gadolinium Doping

Tungsten oxide nanostructures peculiarity and photocatalytic activity for the efficient elimination of the organic pollutant

Synthesis and Applications of Γ-Tungsten Oxide Hierarchical Nanostructures

Preparation and Electrochromic Properties of Nanocrystalline WO3 Thin Films Prepared by Pulsed Excimer Laser Ablation Technique

Nanostructured WO3 films using high temperature anodization

Enhanced Photoelectrochemical Water Oxidation on WO3 Nanoflake Films by Coupling with Amorphous TiO2

Ultraviolet Light-Induced Surface Changes of Tungsten Oxide in Air: Combined Scanning Transmission Electron Microscopy and X-ray Photoelectron Spectroscopy Analysis

Photocatalysis and photoelectrochemical properties of tungsten trioxide nanostructured films

Modification of WS2 thin film properties using high dose gamma irradiation

Platelike Wo3 from Hydrothermal Rf Sputtered Tungsten Thin Films for Photoelectrochemical Water Oxidation

Efficient Photoelectrochemical Water Splitting and Impedance Analysis of WO3−x Nanoflake Electrodes