Abstract:Over the last decade, the global fight against climate change through electrification has led to an increase in research on building heating, ventilation, and air conditioning (HVAC) systems that utilize intelligent control algorithms to provide demand-side grid service while also maintaining the thermal comfort of building occupants. As the pivotal point between building electricity consumption and indoor thermal comfort, high-efficiency electrical vapor-compression heat pumps are at the center of these emerging studies, and various grid-interactive and occupant-comfort control algorithms have been developed for them. The impact of these algorithms on heat pump operation and performance when subjected to different weather conditions, building loads, and grid requests calls for investigation and verification via experimental testing with actual heat pumps integrated with real-time building and grid responses. This study introduces a Water-Source Heat Pump (WSHP) Hardware-in-The-Loop (HIL) Test Facility that is the first of its kind. This testbed utilizes a 2-ton variable speed water-to-air heat pump that is capable of interacting with a virtual environment currently comprised of an EnergyPlus (E+) building simulation, an agent-based occupant behavioral model, and a single U-tube ground-loop heat exchanger (GLHE) model. Detailed descriptions of the testbed’s physical design and operation, virtual environement, as well as their mutual communication is provided. An uncertainty analysis is also performed under manufacturer specified heating and cooling design conditions. This analysis shows that the total load across the WSHP’s demand side heat exchanger, i.e., the sum of its latent and sensible components, can be measured with a relative uncertainty of ± 10.4% and ± 3.6% in cooling and heating mode respectively. The WSHP’s coefficient of performance (COP) can be measured with relative uncertainties of ± 10.4% in cooling mode, and ± 3.7% in heating mode. A preliminary 24-h experimental demonstration is then performed utilizing the DOE prototype small commercial office building model in E+. The simulation takes place in Atlanta, GA on the date of 08/26/15 from 12:00 AM to 11:59 PM using TMY3 weather data. . The results from this demonstration show that over the course of this experiment the simulated outputs of zone dry-bulb temperature, zone humidity ratio, and WSHP inlet water temperature can be tracked by testbed emulators up to a root mean squared error (RMSE) of ± 0.27 °C, ± 0.376 g/kg, and ± 0.85 °C respectively. The WSHP’s dynamic behavioral characteristics and performance are also captured, and correspond well with the authors’ previous understanding of heat pump efficiency as a function of evaporator and condenser fluid inlet conditions respectively.

Evaluation of start-up characteristics for heat pipe-cooled nuclear reactor coupled with recuperated open-air brayton cycle using hardware-in-the-loop

Experimental and Numerical Study on Thermal Hydraulic Performance of Trapezoidal Printed Circuit Heat Exchanger for Supercritical CO2 Brayton Cycle

Simultaneous Optimization of a Heat Exchanger Network and Operating Conditions of Organic Rankine Cycle

Experimental Investigations on Dynamic Performance of Organic Rankine Cycle Integrated with Latent Thermal Energy Storage under Transient Engine Conditions

Development of a hardware-in-the-loop simulator for small-scale concentrated solar combined heat and power system

Startup Analyses of a Megawatt Heat Pipe Cooled Reactor

Coupled Characteristics and Performance of Heat Pipe Cooled Reactor with Closed Brayton Cycle

A transient multiphysics coupling method based on OpenFOAM for heat pipe cooled reactors

Dynamic simulation and optimization of load change operation of high-temperature gas-cooled reactor pebble-bed module

Dynamic Modeling of a HeXe-Cooled Mobile Nuclear Reactor with Closed Brayton Cycle

Temperature Fluctuation Mitigation of Heat Pipe Cooled Reactor with Closed Brayton Cycle During Load-Following Dynamic Power Regulation

Numerical Simulation of the Transient Flow Characteristics and Thermal Stratification Phenomena in the Passive Residual Heat Removal System of NHR-200-II

Performance assessment of a real water source heat pump within a hardware-in-the-loop (HIL) testing environment

Dynamic simulation of a space lithium-cooled reactor system coupled with a He–Xe closed Brayton cycle

Dynamic Simulation and Analysis of Transient Characteristics of a Thermal-to-electrical Conversion System Based on Supercritical CO2 Brayton Cycle in Hypersonic Vehicles

Thermo-hydraulic Experimental Validation of an Integrated Modular Small Reactor Operating in Full Power Natural Circulation

Thermodynamic analysis and optimization of the combined supercritical carbon dioxide Brayton cycle and organic Rankine cycle‐based nuclear hydrogen production system

Transient Analysis of Active Residual Heat Removal Process for Htr-Pm

Development and application of a transient analysis code for heat pipe cooled reactor systems

A new neutronics-thermal-mechanics multi-physics coupling method for heat pipe cooled reactor based on RMC and OpenFOAM

Transient analysis and optimization of passive residual heat removal heat exchanger in advanced nuclear power plant