Abstract:Carbon nanotubes (CNTs) have outstanding characteristics including high mechanical properties, namely tensile strength and elastic modulus,and still remarkable flexibility, excellent thermal and electric conductivities, low percolation thresholds (loading weight at which a sharp drop in resistivity occurs) and high aspect ratios (length to diameter ratio, L/D) while the latter provides the nanotubes with additional advantage over spherical fillers to obtain high property composites. Therefore I CNTs have the potential to act as a reinforcing filler of polymer matrices. The tetraglycidyl-4,4'-diaminodiphenylmethane (TGDDM) cured with 4,4'-diaminodiphenylsulphone WDS) and filled with graphite or carbon fibers are commonly used as a polymeric matrix in high performance composites employed in the aircraft and spacecraft industries. In present paper, multi-walled carbon nanotubes (MWNTs) as a nano-filler were incorporated in the TGDDM/DDS epoxy. The thermal properties of the composites were studied by differential scanning calorimetry (DSC), dynamic thermal analysis (DMTA) and thermal gravitimetric analysis TGA). In addition, the dispersion of MWNTs in the epoxy was also investigated by scanning electron microscopy SEM). In DSC studies, Kissinger and Flynn-Wall-Ozawa (FWO) methods were used to study the nonisothermal cure kinetics of the MWNTs filled TGDDM/DDS composites at different heating rates. The activation energy (E.) of cure reactions of the MWNTs filled epoxy composites was obtained by Kissinger and FWO methods. For all composites, the E. obtained by Kissinger method was slightly less than that of FWO method. With the addition of MWNTs, the E. of the epoxy composites decreased first and then increased with the increase of the MWNTs contents. These results showed that the incorporation of carbon nanotubes accelerated the cure reaction of the TGDDM/DDS epoxy at lower MWNTs content due to the interaction between the hydroxyl groups on the surface of nanotubes and the epoxy. However, due to the high surface energy of carbon nanotubes, the viscosity of MWNTs/epoxy composites increased at higher MWNTs content. Hence, the mobility of hydroxyl groups was hindered, and the reaction energy of composites increased with increasing MWNTs contents. The influence of carbon nanotubes on the thermal stability of the epoxy was studied by TGA. It is shown that MWNTs had little influence on the thermal stability of the cured epoxy. The storage modulus and glass transition temperature of MWNTs filled TGDDM/DDS were investigated by DMTA. It is seen that the storage modulus of TGDDM/DDS system was enhanced with the increasing of MWNTs content, that is, the modulus increased 6.3% and 7.8% at 1 wt % and 5 % MWNTs content, respectively. The glass transition temperature of the epoxy slightly decreased. Furthermore, the DMTA results of MWNTs/TGDDM/DDS composites were compared with that of carbon narrofibers (CNFs)/TGDDM/DDS composites. It was shown that the interactions between CNFs and epoxy were better those between that MWNTs and epoxy. The dispersion of carbon nanotubes in the epoxy was studied by SEM. The SEM results suggest that of MWNTs had poor dispersion in the cured epoxy. However, the radii of carbon nanotubes in the epoxy were greater than those of pure nanotubes. These results show the existence of interaction between carbon nanotubes and epoxy.

Curing behavior, mechanical and thermal properties of epoxy‐CeO 2 nanocomposites

The Curing Behavior and Properties of Diglycidyl Ether of 4,4′-Bis(4-hydroxybenzoyloxy)-3,3′,5,5′-tetramethylbiphenyl and Its Composites with Multi-Wall Carbon Nanotubes

Behavior of epoxy resin filled with nano-SiO<sub>2</sub> treated with a Eugenol epoxy silane

Preparation and properties analysis of CTBN/CeO2 co‐toughened epoxy resin composites

Synergistic effects of nanoparticle geometric shape and post curing on carbon-based nanoparticle reinforced epoxy coatings: Characterization, microstructure, and adhesion properties

Improvement Effect of Functionalized Cnts on Mechanical and Thermal Properties of Epoxy Matrix

Curing Behavior of UV-Initiated Surface-Modified Nano-TiO2/Epoxy Resin Prepolymers and the Properties of Cured Composites

Enhanced thermomechanical properties of epoxy-multiwalled CNT nano-composites

Diatomite‐filled epoxy resin composites: Curing behavior, dielectric, and thermal properties

Reinforcement of Aminopropyl-Terminated Siloxane-Treated Carbon Nanotubes in Epoxy Thermosets: Mechanical and Thermal Properties

CeAlO3 nanoparticle synthesis through combustion-assisted method and structural property assessment in Nano-CeAlO3 polymer composites

Characteristics of Mechanical Properties and Thermal Behavior of Epoxy Nanocomposites and Coatings by Zinc Borate, Nano Silica, and Hardener

The effect of carbon nanotubes loading and processing parameters on the electrical, mechanical, and viscoelastic properties of epoxy-based composites

Thermoanalytical Studies of High Performance Epoxy/Carbon Nanotube Composites

STUDY OF CURING BEHAVIORS OF CARBON NANOTUBES/EPOXY COMPOSITES

Thermo-mechanical properties of epoxy nanocomposites incorporating amino acid and acid functionalized multi-walled carbon nanotubes

Effect of surface functional modification of nano-alumina particles on thermal and mechanical properties of epoxy nanocomposites

Epoxy resin with both ultraviolet shielding and enhanced thermal mechanical properties: Study on synergistic modification of Ce–Zr–Si oxide nanoparticles and basalt fibers

Enhancing mechanical properties of an epoxy resin using “liquid nano-reinforcements”

Carboxyl-terminated Butadiene-Acrylonitrile-toughened Epoxy/carboxyl-Modified Carbon Nanotube Nanocomposites: Thermal and Mechanical Properties

Interaction between carbon nanotubes with functional groups and epoxy resin and its effect on thermal properties of carbon nanotubes/epoxy composites