Abstract:Aerodynamic cooling of hot components/surfaces such as those encountered in gas turbine engines is needed to avoid premature failure of parts due to thermo-mechanical stresses. An effective way of achieving this cooling is through the exchange of heat via effusion/film cooling holes on the hot surfaces. The gases absorb heat as they flow through the cooling holes and also by forming a protective layer of relatively cool gases near the hot surface. Modeling these processes allow for durable design of components and computational simulations offer a complementary way to design new parts or enable performance assessment of the existing parts at new operating conditions. However, in order to perform numerical simulations of heat transfer through effusion holes, the heat conduction through the solid liner and the convection from the gas phase must be coupled considering all the relevant length and time scales. The time scale separation between the solid and the gas phase makes this prohibitively expensive for large scale computations. In applications involving hundreds of effusion holes, resolving the geometry of each effusion hole along with the primary flow (with typically larger length scales) is very challenging. In the current work, we overcome the difficulties associated with the resolution of cooling holes by employing a local source method (Andreini et al, J. Eng. Gas Turb. Power, 2014) to model the heat transfer to the walls. This method is assessed in a canonical configuration based on experiments performed by Gustafsson (Gustaffson, Ph.D. Thesis, 2001).Large Eddy Simulations (LES) coupled with conjugate heat transfer (CHT) models are used in this study. Simulations that resolve the flow passages explicitly using mesh both in the fluid and the solid domains, were used to validate the fidelity of grid resolution, turbulence models and other simulation parameters in predicting velocity fields and wall temperature data. Although, resolving all the effusions passages provides the most accurate results, it is not practical in real applications. Hence, a local source model is employed to model the heat transfer that happens in the cooling-hole passages. In this method, the effusion passage is not resolved (using a mesh) and the mass transfer across the cooling hole passage is prescribed as an injection-extraction boundary condition. The heat transfer at the fluid-solid interface of the cooling-hole passage is also modeled based on Nusselt number correlations available in the literature. This modeling procedure enables simulations with flexible mesh topologies that can be generated at a relatively low cost in comparison to the fully resolved mesh configurations. The local source method is assessed and validated using the available experimental data. The results show that the meshes which resolve the penetration depth in the solid and which conform at the solid-gas interface provide better prediction of the wall temperatures.

Hierarchical heat transfer modeling of a continuous millireactor

Validation of Continuous Conjugate Heat Transfer Model through Experimental Data

Studies on the Critical Heat Flux in Fuel Assembly Using a Modified Two-Phase Multi-Scale Interface Model-Validation and Sensitivity Analysis

An Efficient 3D Tube-Level Flux-Thermal Model of External Tubular Receivers in Solar Power Tower Systems

Comparison of the Prediction of the Temperature Profile in an Ohmic Reactor on Different Modeling Scales

Numerical Modeling and Experimental Validation of Heat Transfer and Flow Resistance on the Shell Side of a Shell-and-tube Heat Exchanger with Flower Baffles

A comprehensive heat transfer prediction model for tubular moving bed heat exchangers using CFD-DEM: Validation and sensitivity analysis

Natural Convection Flow Structures and Heat Transfer in a Model Hydrothermal Growth Reactor

Modeling Effusion Cooling And Conjugate Heat Transfer Using Local Source Method

A Hybrid Numerical Methodology Based on CFD and Porous Medium for Thermal Performance Evaluation of Gas to Gas Micro Heat Exchanger

Three-dimensional Modeling and Sensitivity Analysis of Multi-Tubular Metal Hydride Reactors

Finite difference heat-transfer modeling for continuous casting

Some recent progress in reactor core thermal-hydraulics modelling

CFD Modeling of Heat Exchanger with Small Bent Radius Coils Using Porous Media Model

A New Modeling Method to Evaluate Effective Forced-Convective Heat Transfer Rate of Pipe Flow with Endothermic Chemical Reactions

Multiscale Computational Fluid Dynamics Methodology for Predicting Thermal Performance of Compact Heat Exchangers

A Three-Dimensional Conjugate Model with Realistic Boundary Conditions for Flow and Heat Transfer in an Industry Scale Hydrothermal Autoclave

CFD simulation based on film model of high temperature potassium heat pipe at different positions: Horizontal, vertical, and 45° inclined

Multi-scale Heat Transfer in Fluidized Bed Reactors by Eulerian CFD Modeling

CFD Simulations of a Loss of Heat Sink Experiment in the McMaster Nuclear Reactor

Numerical study of thermal-hydraulic performance enhancement in a shell-and-tube milli-reactor