Abstract:The phenomenon of natural convection and thermal radiation heat transfer in fluid-saturated high temperature packed beds has been widely studied due to its various applications ranging from solar collectors to high temperature gas cooled reactor. With the local thermal non-equilibrium model, the majority of the numerical simulation studies on natural convection and radiation heat transfer in fluid-saturated porous media have limits. In these studies the internal heat transfer coefficients have always been calculated as the existing formulas, which were obtained by the experiments of forced convection in porous media [1-2]. However, natural convection heat transfer in porous media is dominated by the temperature difference between solid particles and fluid, which is different with the forced convection in porous media. For thermal radiation in porous media, the Rosseland diffusion approximation model has always been used in simulations by researchers [3-4], in which the mean absorption coefficient are not calculated according to the experiments and need to be determined by ray-tracing Monte Carlo simulations. Based on high temperature packed pebble beds, this study is aimed to compare the volume-averaged simulations and pore-scale simulations of high temperature packed beds, and predict the effective thermal conductivities of packed beds with temperature up to 1600°C. The effective thermal conductivities of the pebble beds under different temperatures are essential parameters in simulation models to analyze the maximum fuel temperature and temperature distribution in the reactor core in the reactor safety analysis. The SANA test facility was installed at the Research Centre, Julich in Germany specifically to investigate the heat transport mechanisms inside the core of a high temperature gas cooled reactor (HTGR). The validation of the volume-averaged approach and pore-scale approach are based on the experimental data of SANA test [5]. In high temperature helium-saturated annular packed pebble bed, the inner wall has a heat source and the outer wall is isothermally cooled at a lower temperature. The top and bottom walls are kept adiabatic. In the volume-averaged simulations, local thermal nonequilibrium model with the revised internal heat transfer coefficients and radiative heat flux is applied as the energy equation, and no uniform porosity distribution is used. To describe the random packed structure, PFC 3D software is used to simulate the spheres packing, which is used for direct pore-scale numerical simulations. Natural convection and thermal radiation in a 2D circular cross section of the annular pebble bed have been carried out. The effective thermal conductivities and temperature distributions of volume-averaged and pore-scale simulations of the high temperature helium-saturated annular packed pebble bed are corresponded well with the existed experimental data with temperature below 1000°C, and predict the effective thermal conductivities of the pebble bed core with temperature up to 1600°C, which are vital references for thermal hydraulic designs of high temperature gas cooled reactor core. INTRODUCTION Packed beds are widely used in variety of industries, such as catalytic reactors, absorption towers, packed bed regenerators and high temperature gas-cooled reactors. The heat transfer in an enclosure with high temperature packed beds have been gaining interest, because exploring the coupled mechanism of conduction, natural convection and thermal radiation in high temperature packed bed enclosures aids in improving the design of many applications. There are two main approaches for the CFD simulation of the geometry of the closely packed beds: the volume-averaged approach and the pore-scale approach. In the volume-averaged approach, an averaged concept of porosity is applied to simulate the closely packed geometry. As the internal heat transfer between solid particles and fluid is small because of natural convection in the enclosure, the temperature difference between solid and fluid cannot be ignored. So the local thermal non-equilibrium model is quite necessary for high temperature packed beds in an enclosure. Reda [6] has carried out the experimental investigation of a finite vertical cylinder with a heat source at the inner and constant temperature at the outer. The results showed that the radial temperature drop across the annulus was found to systematically depart from the finite-length cylinder as heat power was increased. Rajamani et al [7] have studied the natural convective heat transfer in an annular cylinder embedded with porous medium and discussed

Comparison of the Prediction of the Temperature Profile in an Ohmic Reactor on Different Modeling Scales

Hierarchical heat transfer modeling of a continuous millireactor

Effect of Scale on the Modeling of Radiation Heat Transfer in Packed Pebble Beds

Thermal Simulation and Analysis of Dry-Type Air-Core Reactors Based on Multi-Physics Coupling

Thermal conductivity prediction by atomistic simulation methods: Recent advances and detailed comparison

Validation of Continuous Conjugate Heat Transfer Model through Experimental Data

An Efficient 3D Tube-Level Flux-Thermal Model of External Tubular Receivers in Solar Power Tower Systems

An Analytical Model for Electrochemical Tubular Flow Reactors

Comparison of Volume-Average Simulation and Pore-Scale Simulation of Thermal Radiation and Natural Convection in High Temperature Packed Beds

Modeling Effective Thermal Conductivity of Thermal Radiation for Nuclear Packed Pebble Beds

Prediction of Flow and Temperature Distributions in a High Flux Research Reactor Using the Porous Media Approach

1D Modeling Approach for Heat Transfer in Packed Beds with Embedded Heat Sources

A Reduced-Order Electrochemical Model for Analyzing Temperature Distributions in a Tubular Solid Oxide Fuel Cell Stack

A Thermal Resistance Model of Conduction–thermal Radiation Heat Transfer in Pebble-Bed Nuclear Reactors

Improving the Analysis of Heat Transfer in Packed Beds: A Comparative Study between DEM Simulations and Existing Literature Models

Effects of nanofluid and radiative heat transfer on the double-diffusive forced convection in microreactors

Heat and mass transfer model for a counter-flow moving packed-bed oxidation reactor/heat exchanger

Pore-scale numerical simulation and LTNE analysis for fully-developed forced convective heat transfer in packed beds of mono-sized rough spheres covering near-wall and core regions

Thermal and electrical performance analysis of induction heating based‐thermochemical reactor for heat storage integration into power systems

CFD simulation based on film model of high temperature potassium heat pipe at different positions: Horizontal, vertical, and 45° inclined

Simulation and enhancement of axial temperature distribution in a reactor filled with in-situ electrically heated structured catalyst