Abstract:Flexible pressure sensors that can robustly mimic the function of slow-adapting type I (SA-I) mechanoreceptors are essential for realizing human-like object manipulation in artificial intelligent (AI) robots or amputees. Here, we report a straightforward approach to highly sensitive and robust flexible pressure sensors with fast response time and low operating voltage based on conductive micropyramids made of polydimethylsiloxane/carbon nanotube composites. Both numerical simulations and experimental studies show that the pressure-sensing properties of the devices can be systematically tuned by the spatial arrangement of micropyramids. In particular, by tailoring the ratio between the spacing and the pyramidal base length, the optimal pressure sensors can be achieved with a combination of high sensitivity in both low-pressure (<10 kPa) and medium-pressure (10–100 kPa) regimes, rapid response, high mechanical robustness, low operating voltage, and low power consumption, along with linear response and low hysteresis in the medium-pressure regimes. The optimized pressure sensor is further used for constructing a wearable pressure-sensing system that can convert the amplitude of pressure to wirelessly transmittable frequency signals (spikes) with nearly linear response, closely mimicking SA-I mechanoreceptors. Furthermore, we demonstrate that the high uniformity and scalability of the pressure sensors enable large-area pressure-sensing arrays for spatially resolved pressure mapping.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.0c03659?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.0c03659</a>.Figures S1–S16: characterization, flexibility, and stress–strain curve of PDMS/CNT film; comparison between conductive coating and conductive composites; numerical simulations of the compressibility; pressure response and linearity for a pyramidal array with other base lengths and spacings and with respect to increased CNT loading and tip length; mechanical robustness after overloaded pressure and long-term cyclic compression; low voltage operation and response time; pulse wave detection; setup of wireless communication system; comparison of crosstalk effect; Note S1: effect of the readout circuit to the linearity of the frequency response; Table S1: comparison with other resistive pressure sensors (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.0c03659/suppl_file/nn0c03659_si_001.pdf">PDF</a>)Movie S1: Frequency response in real time (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.0c03659/suppl_file/nn0c03659_si_002.mp4">MP4</a>)Movie S2: Demonstration of wireless communication of spikes (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.0c03659/suppl_file/nn0c03659_si_003.mp4">MP4</a>)Movie S3: Visualization of letter "I" by the pressure-sensing array in real time (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.0c03659/suppl_file/nn0c03659_si_004.mp4">MP4</a>)This article has not yet been cited by other publications.

Bioinspired Engineering of Fillable Gradient Structure into Flexible Capacitive Pressure Sensor Toward Ultra‐High Sensitivity and Wide Working Range

Design and simulation of bio-inspired flexible tactile sensor for prosthesis

A highly sensitive flexible capacitive pressure sensor with wide detection range based on bionic gradient microstructures

Sensitive, Robust, Wide-Range, and High-Consistency Capacitive Tactile Sensors with Ordered Porous Dielectric Microstructures

3D Printed Skin‐Inspired Flexible Pressure Sensor with Gradient Porous Structure for Tunable High Sensitivity and Wide Linearity Range

A programmable, gradient-composition strategy producing synergistic and ultrahigh sensitivity amplification for flexible pressure sensing

Flexible Capacitive Pressure Sensor Based on an Embedded Rib Fabric With a Bionic Sloping Petal Structure

High-Sensitivity Flexible Capacitive Pressure Sensors Based on Biomimetic Hibiscus Flower Microstructures

3D Dielectric Layer Enabled Highly Sensitive Capacitive Pressure Sensors for Wearable Electronics

A Flexible Piezocapacitive Pressure Sensor with Microsphere-Array Electrodes

A high-sensitivity flexible PDMS@rGO-based pressure sensor with ultra-wide working range based on bioinspired gradient hierarchical structure with coplanar electrodes

Flexible Pressure Sensor With High Sensitivity and Fast Response Based on Bionic Honeycomb-Structured Polydimethylsiloxane/Aluminum Oxide Composites Dielectric via 3-D Printing

Bioinspired Hierarchical Structure for an Ultrawide‐Range Multifunctional Flexible Sensor Using Porous Expandable Polyethylene/Loofah‐Like Polyurethane Sponge Material

Multilayer Microstructured High-Sensitive Ultrawide-Range Flexible Pressure Sensor With Modulus Gradient

Multilayer Self-filled Iontronic Pressure Sensor with Ultrahigh Sensitivity and Broad Sensing Range

High-Resolution and High-Sensitivity Flexible Capacitive Pressure Sensors Enhanced by a Transferable Electrode Array and a Micropillar–PVDF Film

A flexible capacitive pressure sensor with a hybrid porous PDMS/SA hydrogel structure for touch/pain detection

A Highly Sensitive and Flexible Capacitive Pressure Sensor Based on a Porous Three-Dimensional PDMS/Microsphere Composite

Bioinspired flexible piezoresistive sensor for high-sensitivity detection of broad pressure range

Biomimetic Nanofiber-Iongel Composites for Flexible Pressure Sensors with Broad Range and Ultra-High Sensitivity

Robust Flexible Pressure Sensors Made from Conductive Micropyramids for Manipulation Tasks